Model #PH060-3C Goodman air-conditioner/heat pump(outside unit)

  • Chassis
    3 Results
  • Coils & Compressors
    3 Results
  • Blower Assembly
    3 Results
  • Control Panel Assembly
    3 Results

Question and Answers

Q:

Need details for new washer, please

A:

Hello Lisa. I will try to help you as much as I can with this washer question. The water temperatures available on that model of washer are shown in the image below. Those are target temperatures. That may not be the actual temperature that you encounter in your particular situation. The tap water temperature and the distance between your washer and the hot water heater can affect the actual temperature that you will encounter in the washer. Those water temperatures are guided by direction from the U.S. Department of Energy.

I do not have details about the exact water level volume. Based on the type of water level pressure switch that is used in this washer, I suspect that a Medium setting on the load size will use the 18 gallons of water (+/- 1 gallon).

The manufacturer does not provide any specifications on the agitator speed. The spin speed is around 700 rpm in the normal spin mode.

The wash time and spin time will vary. The manufacturer does not provide a timing chart or any information that indicates the duration of the wash time and spin time.

There does not appear to be a cycle setting for this washer that will fit the exact needs that you are describing.

I hope that some of this information is useful to you. I know that I was not able to answer all of your questions. If you need more assistance, reply with additional details and I will try to assist you further.

Read More
Lyle W -
Sears Technician
October 31, 2012
A:

Hello Lisa. I viewed that test method before I provided that previous response. That max temperature of 86.75 may not move up much even if you adjust the temperature of the hot water heater. There is a thermistor (temperature sensor) on the inlet water valve assembly that detects incoming water temperature. Based on the temperatures detected, the control will open the cold water valve to mix with the hot water in order to achieve that target temperature of 111 degrees for hot water. The actual water temperature in the tub is often less than that target water temperature. It may be difficult to find a current washer model that will fit those guidelines for that test method. The U.S. Department of Energy imposed strict guidelines on incoming water temperatures for washers over the last several years. The guidelines that I see in that test method are based on a Kenmore or Whirlpool Direct Drive washer that is no longer manufactured. If you are looking for a washer that will come close to those guidelines, then I may be able to research current models and help you. Let me know. Thanks, Lyle.

Read More
Lyle W -
Sears Technician
October 31, 2012
See more answers
Q:

Kenmore 665 Dishwasher Turns On But Does Not Wash

A:

Thank you for your question and I understand your concern. Based on your symptom and details it sounds like the wash motor is not starting and running and only the drain pump will run.

If you hear the wash motor humming and not running then it's likely faulty if capacitor hasn't come disconnected. The motor windings inside the wash motor can be tested using an OHM meter. The wash motor must be disconnected from the electrical connection before testing the motor windings for resistance. To ohm out the start windings place one meter lead on the yellow wire and one on the violet wire and it should measure 6-10 ohms. Check the run winding across the Blue/White wire and the Violet wire and it should measure 3-7 ohms.

I added some images below that will assist you in accessing the wash motor for removal and testing. Note: Disconnect the power supply from the dishwasher before removing and testing the wash motor.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
February 22, 2011
A:

Rick: The ohms resistance when measuring across the Blue wire with the white stripe and the Blue wire with the red stripe should have been between 3-7 ohms. There is also an auxiliary winding in the motor too. Check across the one of the yellow wires to the Blue wire with red stripe should measure 6-10 ohms. The other yellow to blue wire with red stripe should measure 3-7 ohms. Be sure to disconnect the two yellow wires from the capacitor before measuring the resistance. You never did say or not if the wash motor will run or not. If it will run there is nothing wrong with the motor.

Read More
Joey S -
Sears Technician
February 27, 2011
A:

Rick: It seems by your details that the wash motor is not running and the motor windings test within specifications. The next step is to test and verify the voltage supply to the wash motor. Note: I do not recommend checking voltage unless you have experience and you feel safe and confident in doing so, otherwise I recommend calling a service technician to diagnose the failure. The voltage should be checked across the Blue/White wire and the Blue/Red wire.

Read More
Joey S -
Sears Technician
February 28, 2011
See more answers
Q:

Kenmore 665 Dishwasher Turns on But Does Not Wash

A:

Thank you for your question and I understand your concern. Based on your symptom and details it sounds like the wash motor is not starting and running and only the drain pump will run.

If you hear the wash motor humming and not running then it's likely faulty if capacitor hasn't come disconnected. The motor windings inside the wash motor can be tested using an OHM meter. The wash motor must be disconnected from the electrical connection before testing the motor windings for resistance. To ohm out the start windings place one meter lead on the yellow wire and one on the violet wire and it should measure 6-10 ohms. Check the run winding across the Blue/White wire and the Violet wire and it should measure 3-7 ohms.

I added some images below that will assist you in accessing the wash motor for removal and testing. Note: Disconnect the power supply from the dishwasher before removing and testing the wash motor.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
February 22, 2011