Model #MERH752BAW Maytag free standing, electric

  • Control Panel/top Assembly
    3 Results
  • Body
    3 Results
  • Oven/base
    3 Results
  • Door/drawer
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results

Question and Answers

Q:

The broiler element on my Maytag range shorted out and now my oven doesnt work

A:

Thank you for your question and I understand your concern.

 The voltage supply to the bake and broil elements are controlled by the electronic oven control/clock assembly. If the surface elements will continue to operate, I would have to suspect the electronic oven control/clock assemby will need to be replaced. When an oven element shorts/burns out, it can take out the electronic oven control and I suspect this is what happened. Disconnect the power supply from the range before servicing.

The electronic control #5701M758-60 can be ordered from SearsPartsDirect as well as the broil element # W10310249.

 Control Panel removal:

1. Remove maintop assembly, see "Maintop Assembly" procedure.

2. Remove screws securing control panel heat shield.

3. Remove screws securing bottom outside edges of the control panel.

4. Pull unit out from the wall far enough to allow the

back outside screws to be loosened.

5. Loosen the back outside screws securing control

panel to backguard.

6. Grasp front lower outside edges of the control panel and push inward on the outside edges of the backguard to release the control panel front.

NOTE: Front edges of the control panel are difficult to release from backguard.

 Maintop Assembly (Smoothtop Models) removal:

1. Turn power off.

2. Open oven door and remove screws securing maintop to oven chassis, located on the outside edges of the maintop.

3. Raise the front edge of the maintop and pull forward approximately 6 inches.

4. Label and disconnect wire terminal plugs from the maintop assembly.

5. Lift maintop assembly from the oven chassis.

6. Reverse procedures to reinstall maintop assembly.

 Control Board Assembly removal:

1. Remove control panel, see “Control Panel” procedure, steps 1 through 6.

2. Remove screws securing control board bracket to control panel.

3. Label and disconnect terminal plug from control board assembly.

4. Reverse procedures to reinstall control board assembly.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 

Read More
Joey S -
Sears Technician
February 18, 2013
Q:

No heat form any element or oven. MERH752BAW Maytag Maytag cooking

A:

Hello Steve. I am sorry to hear about this problem that you are having with your Maytag Range Model MERH752BAW.

 

Even though you indicated that you have 220 VAC (volts AC) supplied to the range, your symptoms indicate that you are missing the L1 leg of power that is traced in green (actual wire color is black) in the image below. Your details seem to indicate that the 110 VAC L2 leg of 220 VAC is powering up that 110 VAC L1 leg of power through the surface element as traced in that wiring diagram. That is apparently why the clock is powering up when you turn on a surface element.

 

Based on this explanation, I recommend that you re-check the power supply going to the range. Check the house circuit breakers or house fuses for the circuit that supplies the range electrical outlet. If you find no problems with that issue, then I recommend that you check the range electrical outlet as shown in this brief video: Perform a Voltage Check on a 240 Volt Outlet. 

 

If that outlet voltage is okay, then you could have a bad outlet cord or a wiring failure at the terminal block on the back of the range. Let us know if you need help checking these issues.

 

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services Range Repair. 

Read More
Lyle W -
Sears Technician
June 21, 2013

Top Parts