Model #MER6770AAW Maytag free standing, electric

  • Control Panel
    3 Results
  • Top Assembly
    3 Results
  • Body
    3 Results
  • Oven
    3 Results
  • Door (upper)
    3 Results
  • Door (lower)
    3 Results
  • Wiring Information
    3 Results
  • Wiring Information
    3 Results
  • Wiring Information
    3 Results

Question and Answers

Q:

How do I change the main top assembly on my Maytag range model MER6770AAW?

A:

The procedure for removing the glass cook top and the elements on this type of range is shown in the image below. Be sure that you unplug the range to disconnect electrical power before beginning this procedure. Arrange a flat padded surface that you can lay the cook tops down on in order to transfer the elements to the new cook top. After unplugging the range, remove the old cook top and place it on the padded surface with the bottom sticking up so that you can transfer the elements to the new cook top. Transfer the elements to the new cook top and install the new cook top on the range. Plug the range in and test the elements.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
November 06, 2009
Q:

I own a maytag gemini double oven- #mer6770aaw. I replaced the oven contol and forgot to label the wires when replacing the unit and need help.

A:

The first image shows a wiring schematic and the second image shows a wiring diagram for this range. This information should help you connect those wires. If you need more assistance, reply with additional details and we will try to assist you further.

NOTE: The wires must be connected properly to the control board. If you are not certain how to connect the wires using the information shown below, I recommend that you have a service technician connect those wires. Here is a link for the Sears Service website: Sears Home Services .

Read More
Lyle W -
Sears Technician
June 30, 2011
Q:

Maytag Gemini upper oven not reaching temperature.

A:

I have provided you with an image below. The image has the intrusions for removing the sensor and how to enter the test mode. I recommend trying the test mode first. Once you are in the test mode push the upper bake button. This should turn the element on. If the element does not come on, I recommend ohming the bake element. To ohm the element unplug the range and remove the screws securing the element. Pull the element out slightly but be careful not to pull the wires off. Once the element is out you can remove the wires from the element. Make sure you do not let go of the wires because they can accidentally go back into the hole and then you have to take the back apart to retrieve them. I recommend tying a piece of string to them before you let then go. Once the wires are removed set you meter to ohms and place one meter lead on each terminal. The reading should be around 25 ohms. If you get a reading of open, you need to replace the element. If your reading is 25 ohms, the problem is most likely the oven control board.

If the element is heating but the oven is not coming up to temperature I recommend checking the oven temperature sensor. The instructions for removing the sensor are in the image below. Before unplugging the sensor make sure, the wires will not go back into the hole just like on the element wires. Then ohm the sensor using the chart in the image. At room temperature, your reading should be around 1100 ohms. If the reading is off by quite a bit you need to replace the sensor. If the reading is within specs reinstall the sensor and ohm it out from the control board. If your ohm reading is within specs at the control, you have a faulty oven control board. Make sure the range is unplugged before you attempt any repair.

If you need further assistance, please submit more details.

Thank you for using Manage my life.

Here is a link to order any parts you need. Sears Parts Direct .

Read More
Mark T -
Sears Technician
September 06, 2010

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show