Model #MAC 4900 11-600498-01 Mcculloch chainsaw

  • General
    3 Results
  • Chain Break
    3 Results
  • Engine
    3 Results
  • Rear Handle
    3 Results
  • Carburetor
    3 Results

Question and Answers

Q:

my Kenmore he 3t washer stopped with error code 11 F, I followed trouble shooting guidlines, and it flashed a code of C:01. What does this mean. Help.

A:

Hi Karen,

Thank you for submitting a question to Manage My Life.

I am sorry you are having problems with your washer.

Without a model number I will only be able to offer generic information. The f11 error in this type of washer is generally a problem with the main control or the door lock assembly, but it can also be a communication problem between the main and motor control.

To determine the cause of the f11 error you will need a volt/ohm meter and live voltage checks will have to be made. If you have a meter and are comfortable making live voltage checks, reply to this post with a complete model number.

In the meantime you can open the door by removing the toe panel (see image below), and reaching up through the bottom and releasing the door lock assembly. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. There may be a door lock release cord hanging down (resembles weed eater cord) behind the toe panel. If not you will have to feel around to find the tab on the door lock assembly. Pull down on this tab.

I highly recommend having a trained service technician evaluate this problem. You can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
June 06, 2011
Q:

McCulloch MAC 160S Chainsaw

A:

Thank you for your question.

 

I am sorry you are having a problem with the chain saw. If the chain will not tighten when you loosen the nuts and turn the adjusting screw, I suspect the adjustment pin on the clutch cover is broken or not positioned in the bar. I found a video that shows how to replace the adjustment pin. The video also shows how the pin should fit into the bar. Click here to watch the video. 

 

I hope this is helpful. Please let me know if you need further assistance.

 

 

 

 

Thank you for using Manage my life.

 

Mark T.

Read More
Mark T -
Sears Technician
November 05, 2013
Q:

McCulloch Mac 2816 weed wacker

A:

Thank you for your question.

I am sorry you are having a problem with the trimmer. If you have installed a module and still do not have spark I recommend removing the kill wire and check for spark with a new plug. If you still do not have spark double check the air gap between the module and the magnet on the flywheel. The air gap should be set between .010 to .012. Then check for spark. If there still is no spark, the problem is either a weak flywheel magnet or defective module. If the magnet holds a screwdriver, it should be fine.

I hope this is helpful. Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
June 20, 2011
A:

Thank you for the reply. If the kill wire is removed from the module, when you are checking for spark it will not matter if it is frayed. You can repair the wire later once you have spark. If the magnet is fine and the air gap is set, you should have spark. If you do not have spark I suspect a defective module. I know it is not likely but everything else is fine. Just make sure you are using a know good plug and it is grounded to a clean ground when checking for spark. I hope this is helpful.

Read More
Mark T -
Sears Technician
June 21, 2011
A:

By what you have stated you have done, I suspect the module is defective. If you happen to have the old module, you might want to install it and check for spark with the kill wire disconnected. If you have spark, repair the kill wire. If you do not have spark I recommend replacing the module.

Read More
Mark T -
Sears Technician
June 22, 2011
A:

The coil has to be having a good connection to the engine block. This is important for the module to generate the spark. By everything you done so far, I suspect the problem is a defective module. I know it seems unlikely but the checks done point to the module.

Read More
Mark T -
Sears Technician
June 23, 2011
A:

We are missing something somewhere. Try to set the air gap at .012. While tightening the screws, make sure the module does not turn away from the flywheel. Then check for spark with out the spark plug. To do this, insert a screwdriver where the spark plug would go. Then hold the shank of the screwdriver about a 1/8 inch or so from the block. While holding the screwdriver in this position, turn the engine over. You should see a spark jump from the shank to the block. If you get spark the plug is causing the problem. Please let me know what you find.

Read More
Mark T -
Sears Technician
June 27, 2011
See more answers