Model #HL-730 Brother printer

  • No Image Available - Wards
    3 Results

Question and Answers

Q:

How to replace nozzle on Heat gun

A:

Thank you for your question and I understand your concern.

We do not have any technical information or a service manual for you heat gun. It appears by looking at an image of it, remove all exposed screws in order to separate the housing apart. Once the housing has been separated, you should be able to see how the nozzle is attached and how it would come off.

I added a PDF file of an Owner's Manual that will likely apply to your model which shows screws securing the two halve of the case together. It looks like all the Steinel models basically come apart the same way. Take the screws out and pry the two halves apart to access the nozzle. 

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
August 27, 2013
Q:

failure codes

A:

As Alina pointed out, having a model number would help us more accurately decipher the error codes that you are seeing on the washer. The dl error code often pertains to the door lock assembly. The hl can indicate a problem with the temperature sensor on certain washers.

I recommend that you reply with the full model number of your dishwasher. Once we receive additional information, we will gladly provide troubleshooting and repair information.

Read More
Lyle W -
Sears Technician
January 28, 2011
Q:

Proform 730 motor runs fine, then stops

A:

Thank you for your question.  There are a few reasons your treadmill is slowing down or stop when you step on the belt.  1. If the walking belt or drive belt is too loose the treadmill will slow down when you walk on it, but it will not slow down if it is running with no load. That is because the belt is slipping. If you only adjusted the walking belt and not the drive belt, the drive belt could be slipping. To adjust the drive belt you will have to remove the motor hood. The drive belt is located between the motor and the front roller. To adjust the drive belt first, unplug the treadmill and remove the motor cover. Next, locate and loosen the motor mounting bolts. Then move the motor so that the belt is tight and have someone retighten the mounting bolts. It will take quite a bit of force to hold the belt tight. After the belt is tight plug the treadmill in and carefully test the operation. If the belt still slips, watch the front roller. If the roller stops but the pulley does not the roller is defective. If the roller and the pulley stop, the drive belt is still loose.    As far as the walking belt goes, it should be adjusted to be able to lift it approximately 2 to 3 inches at either side of the middle of the belt. I have provided the instructions for adjusting the walking belt below. 2. If the walking belt slows down under a load and both belts are adjusted correctly the walking belt could be dry and in need of lubrication, especially if you have it in a garage. Having it in a garage is a not a good thing the dust and dirt get into the wax on the bottom of the walking belt and grind down the walking board surface causing drag. A dry walking belt is the most likely the problem.To correct this problem apply some deck wax, NOT Silicone, to the walking board. There is a lube kit available as well as a single tube. Both come with installation instructions, the part number for a single tube of wax is 219168 for $3.99, the part number for the kit which includes 3 tubes of wax, an application wand and a case is 219170 for $29.99 and they are available at Sears Partsdirect . Just in case the lube does not come with instructions, I will add them. Turn the walking belt until the belt seam is along the top of the front roller. Raise the belt on one side in the center of the walking board front to back as high as you can. Apply 1/2 the tube of lubrication to the walking board in a zig zag fashion moving from front to back. Move the belt until the seam comes up on top of the rear roller and lift the belt again and put the rest of the lubrication on the walking board in the same manner. Turn the treadmill on and walk on the belt for 10-20 minutes. Walk all over the belt to distribute the lubrication evenly on the walking belt and board. I hope this helps. If I can be of further assistance, please feel free to reply below.  Thanks for using Manage My Life. Mark T.

Read More
Mark T -
Sears Technician
March 04, 2013