Model #H-70-0-02 Yukon furnace/heater, oil

  • Casing Assembly
    3 Results
  • Blower Assembly
    3 Results
  • Combustion Chamber Assembly
    3 Results
  • Vent & Drain Assembly
    3 Results
  • Combustion Heat Coil Assembly
    3 Results
  • Front Coil Collector Box Door Assembly
    3 Results
  • Hs Burner
    3 Results
  • Electric Control Box Assy.
    3 Results

Question and Answers

Q:

he3t stops during rinse

A:

The technical details of the FH error code are provided in the first image below. Since you are not getting this failure during the initial fill, I recommend that you check the installation of the drain hose to make sure that it complies with the guidelines in the owner's manual. Here is a link for the owner's manual in case you need it: Owner's Manual . Make sure that the drain hose is not pushed way down into the stand pipe. This can cause a siphoning of fill water out of the washer during the rinse fill.

Since the rinse cycle normally uses cold water on the HE3t washer (or warm water in the Warm/Warm setting), you could have a problem with the cold water line or fill valve. Make sure that the cold water line is not kinked and that the cold fill faucet in back of the washer is all of the way open. Shut the cold water valve and pull the hose off of the connection on the back of the washer. Place the end of the hose in a bucket and briefly turn on the cold water fill faucet to verify that you have proper water pressure and flow from the cold water fill hose. You can check the hot water hose in the same manner if you think it is necessary. Check the inlet screen for the inlet water valve assembly on the back of the washer for debris or deposits that could be inhibiting inlet water flow. If you find excessive debris and deposits, I recommend that you replace the inlet water valve assembly. Cleaning this screen can be risky since some of the foreign material could make it into the inlet water solenoid valve and cause it to stick open. This would result in a flood of your laundry room (and house). You can order a new inlet water valve assembly for the washer from the Sears PartsDirect website. Unplug the washer and shut off the water supply before accessing internal components in the washer. Remove the top panel of the washer to access the inlet water valve assembly. Remove the screws at the very back of the top panel and then move it back slightly. Lift is up and off of the top of the washer. Note the position of the wires connected to the inlet water valve assembly. Remove the wires and the hoses from the valve. Remove and replace the valve. Reconnect the hoses and wires. Reassemble the washer.

These tips will likely help you resolve this FH error code problem. If you need more help, submit additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 10, 2010
Q:

I have a Kenmore Elite H E 3 electric dryer that doesn't work.

A:

Thank you for your question and I understand your concern.

The "E2" error code indicates a shorted thermistor. The thermistor will need to be disconnected and tested with an Ohm meter to see if it's shorted. I added a couple of images below with the troubleshooting steps how to access the thermistor and thermal fuse. Note: Disconnect the power cord from the power source before removing the lower access panel.

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
April 21, 2012
A:

Bill: The 02 is just a number used for the engineers. If you hear a faint click from the control board when start is pushed, then I would suspect a faulty thermal fuse. Disconnect the power supply from the dryer and access the thermal fuse. Disconnect the thermal fuse and check it for continuity with and Ohm meter. You will likely find it faulty.

Read More
Joey S -
Sears Technician
April 21, 2012
A:

Bill: I'm glad you found the problem. Make sure the vent hose and vent system is not restricted. Check outside and make sure the damper door on the vent hood is opening too. Thanks for using Manage My Life. Have a great day.

Read More
Joey S -
Sears Technician
April 21, 2012
See more answers
Q:

I h

A:

You could have a problem with the burner switch or the element itself. Without the model number for your range, it is difficult to offer more specific troubleshooting help. I recommend that you reply with the full model number of your range if you want to fix this problem yourself. The model number on many of the Kenmore electric ranges is on the base in front of the right or left front leveling leg (see image below).

Read More
Lyle W -
Sears Technician
February 24, 2011