Model #DS-20 Kenmore smoker

  • Replacement Parts
    3 Results
  • Hardware
    3 Results

Question and Answers

Q:

I have a pro form 630ds. It shuts off while I'm walking on it. It throws the breaker.

A:

I am assuming the treadmill trips the breaker on the treadmill. If this is the case several things can cause it.

You might have a weak circuit breaker. Replacing the circuit breaker might cure the problem.

If you are using an extension cord on the treadmill, try moving the treadmill and connecting it to a wall outlet. The extension cord might not be heavy enough for the treadmill.

If the walking belt on the treadmill is dry and needs lubrication, it will cause the drive motor to draw excessive amps. To test the walking belt lubrication, do not turn the treadmill motor on. Set the elevation to the highest level. Stand near the front of the walking belt. Push yourself firmly toward the rear of the treadmill. If the belt is properly lubricated the belt will take you to the rear edge of the treadmill and dump you off on the floor. If you move and stop, the belt needs lubricating.

The part number for the belt lubrication kit is 219168. You can buy it at [www.searspartsdirect.com]. The cost is around $4.00. The application instructions should be in the package, but in case they are not here is how to apply the lubrication.

Turn the walking belt until the belt seam is along the top of the front roller. Raise the belt on one side in the center of the walking board front to back as high as you can. Apply ½ the tube of lubrication to the walking board in a zig zag fashion moving from front to back. Move the belt until the seam comes up on top of the rear roller and lift the belt again and put the rest of the lubrication on the walking board in the same manner. Turn the treadmill on and walk on the belt for 10-20 minutes. Walk all over the belt to distribute the lubrication evenly on the walking belt and board.

Read More
Jimmy K -
Sears Technician
August 25, 2009
Q:

What does F 20 mean

A:

Thank you for your question and I understand your concern. Without having the model number of your washer I will only be able to provide general information.

Generally speaking, the "F20" means no water is detected entering the tub or the pressure switch trip was not detected.

There is a good possibility the reason why is because some or all the water is coming out the dispenser. The reason why it's coming out of the dispenser is most likely due to a small garment was shoved up into the tube that delivers the water into the tub. This can happen if the washer is overloaded or if the garment is too small. Small garments should be placed in a garment bag before washing.

Remove the dispenser drawer and confirm there is no block there and then open the door and look at the rubber boot at about the 10 or 11 o'clock position and you should see where the water enters the tub. You will likely find a small garment up inside the tube restricting the fill water from entering the tub and causing the F20.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 12, 2011
Q:

F 20

A:

The F20 indicates that the control is detecting a water fill problem. The technical explanation of that code is shown in the image below. I recommend that you conduct the troubleshooting described in that document. If the washer is not filling, you could have a problem with the water supply or fill hose. A bad inlet water valve assembly could also cause this failure.

If the washer is filling, you could have a bad water level pressure switch or a failed control board.

This information may help you determine the cause of your F20 code in the washer. If you need parts, you can order them from the Sears PartsDirect website. Be sure that you unplug the washer before accessing internal components.

If you need more help, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
August 06, 2011
A:

Hello Scott. If the washer is filling with a large amount of water but it not being detected by the pressure switch, then the pressure switch or the air tube on the pressure switch is probably causing this failure. If the washer is not filling, you could have a problem with that control board or the water valves. Reply with the model number of your washer and the tests that you performed to narrow your failure down to the pressure switch or the control board. We will assist you further once we receive more information.

Read More
Lyle W -
Sears Technician
August 22, 2011
A:

Thanks for adding that model number. If you just ran that rinse drain and spin cycle, the washer may have only used the cold water valve. You could have a problem with that hot water inlet valve. I recommend that you run the diagnostic test shown in the first image below to check the hot water valve. You can use that manual diagnostic test as well if needed. This should help you determine whether you have a problem with that hot water valve. Based on your description, this troubleshooting may help. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
August 22, 2011
A:

Hello Terry. It would be unusual (but possible) for the water level pressure switch to go bad that quickly. The control will often display the F35 code if it senses that the pressure switch is bad in your model. The technical information for the F20 code is shown in the image below. Check to see if the washer is filling with water. If not, you could have a problem with the water valves. Make sure that the hot water faucet is fully open. A problem with the hot water supply (or not providing a hot water supply) to the washer can cause this code. A problem with the flow meter could also trip that code. I recommend that you check to see if the washer is filling and determine when the code is displayed (30 seconds or 13 minutes). Reply with those details and we will assist you further.

Read More
Lyle W -
Sears Technician
December 27, 2011
A:

Based on the timing of that F20 code, you may have a leak in the air hose between the bottom of the tub and the pressure switch or a problem with that flow meter. I recommend that you UNPLUG the washer and remove the top cover as shown in the first image below. If the washer still has water in the tub, you can remove the air hose from the pressure switch and gently blow into it to check for an air leak. If the hose is leaking, it will need to be replaced. You can order parts from the Sears PartsDirect.com website (see link below). The second image shows how to remove the back panel and remove that air hose connection on the back bottom portion of the outer tub assembly. If that air hose is okay, then you can check the wiring connections on that flow meter. The third image shows that flow meter (circled in red) on the parts diagram for that portion of your washer. The 4th image shows how to access and replace that flow meter. You can use that information in the 4th image to check the wiring connections. If all of the wiring connections are okay, then you may need to replace that flow meter to fix this F20 failure. Be sure that you have the washer UNPLUGGED when accessing internal components. I hope that these additional tips help. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
December 29, 2011
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
December 29, 2011
A:

Hello Terry. Thanks for the feedback and letting us know how this situation was resolved. That can help other customers with this same problem. Let us know if you ever need more help.

Read More
Lyle W -
Sears Technician
January 05, 2012
See more answers