Model #AP-08CK1FDS Wintair air conditioner -room

  • Cabinet Parts
    3 Results

Question and Answers

Q:

Why does my Kenmore HE washer model 110.45088403 say "controls locked" making it unusable?

A:

Press and hold the DRAIN & SPIN button for 3 deliberate seconds until the CONTROL LOCKED status light goes out. This should unlock the controls so that they will work normally.

Here is a link for the owner's manual for your washer in case you need it: Owner's Manual .

If the controls will not unlock using the above procedure, try unplugging the washer for 5 minutes and then plugging it back in. Try holding the DRAIN & SPIN button for longer to unlock the controls if necessary. If you still have trouble unlocking the controls then the washer will likely need service. Here is a link for the Sears Service website in case you need it: Sears Home Services .

Read More
Lyle W -
Sears Technician
March 26, 2010
Q:

i have a kitchen aid dryer model kgy777ezo. blower wheel freezes ap and wont turn. i manually freed it last week and the problem started again today. any though

A:

Thank you for your question and I understand your concern. Since the blower wheel is threaded onto the motor shaft, I must assume the motor is seizing and will need to be removed and replaced providing that there is no type of object laying in the bottom of the blower housing jamming the blower wheel.

For your information, the model number you provided was mis read. It should be KGYE777BWH0. The motor can be ordered from Sears PartsDirect

I added the basic instructions in the image below. NOTE: Disconnect the power cord before removing the front panel.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 12, 2011
Q:

Craftsman lawn tractor dr belt

A:

Thank you for your question.

I am sorry you are having a problem with replacing the belt on the tractor. I have checked the dimensions of the belt and it should be 1/2" x 90". The easiest way I have found to replace the drive belt is to remove the mower deck. Once the deck is removed, you have better access to the belt. I have provided you the instructions for removing the deck and installing the belt. After you have the belt on, I recommend testing the operation before installing the deck. If it is ok go ahead, clean the bottom side of the mower deck, and reinstall it.

Please let me know if you need further assistance on the repair of the tractor.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
April 25, 2011
A:

Thank you for your question.

I am sorry you are having a problem with replacing the belt on the tractor. I have checked the dimensions of the belt and it should be 1/2" x 90". The easiest way I have found to replace the drive belt is to remove the mower deck. Once the deck is removed, you have better access to the belt. I have provided you the instructions for removing the deck and installing the belt. After you have the belt on, I recommend testing the operation before installing the deck. If it is ok go ahead, clean the bottom side of the mower deck, and reinstall it.

Please let me know if you need further assistance on the repair of the tractor.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
April 25, 2011
See more answers