Model #WT200LE TYPE 3 WEEDEATER Blower, Gas

  • Housing/handle
    3 Results
  • Cylinder/crankshaft/crankcase
    3 Results
  • Vacuum Bag/tube
    3 Results
  • Carburetor #530071465 (c1q-w11)
    3 Results
  • Carburetor #530071632 (c1q-w11c)
    3 Results
Find part by diagram >

Question and Answers

Q:

3 in 1 Lawn Tractor blade type

A:

Thank you for your question.

The 3 in 1 blade is used for mulching, bagging, and side discharge. We have used this blade for years and it work good for all 3.

I hope this is helpful. Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
May 15, 2012
Q:

wt200le "Wild Thing" leaf blower will not start

A:

Thank you for your question.

I am sorry you are having a problem with the blower. If the fuel mixture in the blower is older than 5 weeks old, it should be drained. Then refill with fresh fuel mix. If this does not help I suspect there is a problem with the fuel system. I recommend checking in the fuel tank first. When you look in you see a fuel line with a white filter attached to the end. Then inspect the fuel line. If it is hard and brittle, it has to be replaced. Here is a video that shows how to replace the fuel line. If the fuel line is fine, I suspect the carburetor is to blame. The carburetor will have to be cleaned or replaced. Here is a video that show how to clean the carburetor. Before you remove the carburetor, make sure to note the fuel line and cable connections. This will save a lot of frustration latter.

Here is a link to order any parts you need. Sears Parts Direct .

I hope this helpful. If you need further assistance, please reply below with more details.

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
July 16, 2011
Q:

Gas Edger does not start - Weed Eater PE 550 type 3

A:

I am sorry you are having a problem with the edger. You indicated that you replaced the fuel lines. I assume that you replaced the fuel pick-up/filter inside the tank. Make sure that you have the proper mix of fresh fuel/oil in the tank. Make sure that you have enough fuel/oil mix in the tank and that the pick-up/filter is submerged in the fuel.

 

The engine needs three things to run. They are fuel, compression and spark. Let’s check for those first. Try to start the engine as you normally do. After you pull the rope, a few times remove the spark plug. The end of it should be wet if it is getting fuel. If not, then you probably have a fuel line problem since you just replaced the carburetor.

 

If the spark plug is wet after try to start the engine, I recommend checking for spark. Allow the spark plug to dry before testing the spark. Conduct that test away from the cylinder. I found a video that will aid in checking for spark. Here  is the video. That video shows a chain saw but the process will be the same for your edger. If you are not getting spark then you may have a bad spark plug or a failed ignition module.

 

If you have spark I recommend checking for compression. To do this you need a compression gauge. You should be able to loan one from Auto zone. They have a loan a tool program. Once you have the gauge installed pull the rope a few times fast. You should have a reading of at least 90 psi. If you do not have this reading there is a problem in the cylinder. This type of repair usually exceeds the valve of the unit.

 

You can order parts from this page: Weed Eater Gas Edger Model PE 550 Type 3 Repair Parts.  

 

If you need more help, reply with additional details and we will assist you further.

 

If you get to the point where you need to have a service technician examine and repair the edger, you can carry it into your nearest Sears Store or Sears Repair Center. Here is a link that provides more information about locations and repair service: Sears Yard Tool Repair Service. 

Read More
Lyle W -
Sears Technician
March 25, 2013
A:

If you are missing a screw on that carburetor, that could be causing your problem.

Read More
Lyle W -
Sears Technician
March 25, 2013
A:

Your details indicate that you are not getting fuel to the cylinder. The problem with the loose fastener on the carburetor and the cylinder assembly. The system is probably not able to pull a vacuum and suck gas into the cylinder due to those leaks. I recommend that you resolve those issues and then see if you are getting gas into the cylinder.

Read More
Lyle W -
Sears Technician
March 26, 2013
See more answers