Model #TR-19D AMANA Top-Mount Refrigerator

  • (ta-14d) (ta-14ld)
    3 Results
  • (ta-14d) (ta-14ld)
    3 Results
  • (t-17d-1) (t-17ld-1) (ti-17d-1) (ti-17ld-1) (tr-17d-1) (tr-17ld-1) (tri-17d-1) (tri-17ld-1)
    3 Results
  • Machine Compartment Parts (t-17d-1) (t-17ld-1) (ti-17d-1) (ti-17ld-1) (tr-17d-1) (tr-17ld-1) (tri-17d-1) (tri-17ld-1)
    3 Results
  • (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Interior Parts (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Interior Parts (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Freezer Interior (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Evaporator (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Compressor And Condenser (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Controls (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Ice Maker And Parts (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Miscellaneous Parts (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Door Hinges And Door Parts (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
  • Machine Compartment Parts (tr-19d) (tr-19ld) (tci-19d) (tci-19ld)
    3 Results
Find part by diagram >

Question and Answers

Q:

I have a Kenmore Refrigerator model 106.55522400 and the evaporator try part number 1105523 over flowed. Where did the water come from? How do you remove the tr

A:

This tray is not designed to be removed. Removing excess water with a baster is the normal method for draining this tray.

It is a drain pan that collects condensate water from the ice/frost that is melted off of the evaporator during the automatic defrost process. Once every 8 hours or so, the compressor will shut off and the control will energize a heater that is positioned around the evaporator fins inside the back wall of the freezer. This will melt off any frost/ice that has built up on the evaporator. The condensate water drips down into a pan below the evaporator and then drains down into the tray that you are describing. Normally, the heat and air flow through the machine compartment in the bottom of the refrigerator will evaporate this condensate water off before the next automatic defrost cycle begins. Excessive humidity, a warm air leak into the refrigerator/freezer or poor air flow through the machine compartment could be inhibiting the evaporation process and causing the tray to overflow. Check the door seals on the refrigerator and freezer for any damage or loose spots. Replace the seals if necessary. If you are in a humid climate or the refrigerator is in a garage where it is not air conditioned, the overflow of this tray can be somewhat normal. Try cleaning the front grill and the condenser coils. Make sure that the back bottom panel is in place on the outside back of the unit. Make sure that your condenser fan is running.

If you still have problems with the tray overflowing, you may need to have a service technician examine the refrigerator. Here is a link for the Sears Service website in case you need it: Sears Home Services .

Read More
Lyle W -
Sears Technician
May 28, 2010
Q:

Kenmore Elite Microwave dead - burnt wire smell - is it fixable?

A:

That microwave does have several fuses and other inexpensive components that could have caused this problem. Since you smelled the burning wires, it is likely that you will need more than just fuses to repair this microwave. It would require a service technician to diagnose and repair this problem. I don't recommend that you attempt to repair a microwave yourself. They contain high voltage components that can retain a lethal electrical charge even when the microwave is completely unplugged.

Based on your description, I recommend that you replace the microwave instead of having it repaired. This recommendation is based on the age of the microwave and the likely cost of the repair.

You can normally find a replacement for just over $200 if you are price conscious. Here is a Sears.com link for a Kenmore microwave that is inexpensive: Kenmore Stainless Steel 30 in. Microhood Combination - 8503 .

You can find other models on the Sears.com website as well.

If you want to have the microwave repaired, you can click on this link to visit the Sears Service website: Sears Home Services .

I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
December 22, 2010
Q:

Proform treadmill model 831.29325.0 what electrical part to replace to fix a problem of belt hesitation - no mechanical problem found, motor brushes OK

A:

Based on your symptom the likely cause is a lack of belt lubrication causing friction between the walking belt and the deck. To test the belt for a friction issue, do not turn the treadmill motor on. Set the elevation/incline to the highest level. Stand near the front of the walking belt. Push yourself firmly toward the rear of the treadmill. If the belt is properly lubricated the walking belt should rotate and take you to the rear edge of the treadmill and dump you off on the floor. If you move and stop, the belt needs lubricating. The part number for the belt lubrication kit is 219168. The lubrication can be ordered from Sears Parts Direct and shipped to you.

Read More
Joey S -
Sears Technician
May 17, 2010