Model #SC150E-2-4.2 CLIMETTE/KEEPRITE/ZONEAIRE Package Units(both units combined)

  • Model Notes
    3 Results
  • Functional Horizontal Coils/erh56xa3
    3 Results
  • Functional Replacement Parts/erh84xa4
    3 Results
  • Functional Replacement Parts/eh120x2
    3 Results
  • Functional Replacement Parts/ak144et
    3 Results
  • Functional Replacement Parts/ph150x2
    3 Results
  • Functional Replacement Parts/ak123at
    3 Results
  • Functional Replacement Parts/prh56xa3
    3 Results
  • Functional Replacement Parts/ph120x2
    3 Results
Find part by diagram >

Question and Answers

Q:

gas/oil mix ratio for champion 1947 outboard motor

A:

Thank you for your question on the gas to oil mix on the outboard motor.

Back in those days they did not have a high quality 2 cycle oil. I do not remember any special 2 cycle oil the just used standard 30 weight. The 2 cycle oil is low ash low deposit oil so it would not collect so many deposits in the engine and will lubricate the internal engine parts and burn cleaner.

The mix at that time was 16:1 or 8oz. oil to 1 gal. of gas.

I hope this will help.

Sam A.

Read More
Sam A -
Sears Technician
August 28, 2012
A:

Thank you for your question on the mix ratio for this old engine. I would be afraid to go much beyond 32:1 ratio. But seeing as you are using a very high quality 2 cycle oil I would chance 32:1. You do not know how these old engines will respond to the lighter oil even though they are much higher quality than the old 30 weight standard oil when this engine was produced. I would hat to see you seize up a good old outboard engine like that. These old engines had different metal mixes in the combustion parts than they do with modern engines. And I would also be concerned about the alcohol in the fuel and would suggest that for this engine you use some fuel treatment to combat the new fuel issues. Sam A.

Read More
Sam A -
Sears Technician
October 11, 2012
See more answers
Q:

HE 2 plus11047532600

A:

Hi Russell,

         

Thank you for submitting a question to Manage My Life.

         

I assume you are talking about the front lower counter weight. This is most likely due to an issue with the door boot or the tub is cracked. You will have to determine where the leak is coming from. I am including a set of images below that will help you with disassembly. The images may not be exactly like your washer but they will give you the basic idea. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

         

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

         

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

         

I hope this is helpful. If I may be of further assistance please reply to this post.

         

Landell

Read More
Landell -
Sears Technician
February 11, 2012
Q:

Kenmore HE 2 plus

A:

Hello Kelly. I am sorry to hear about the F21 code problem that you are having with your Kenmore HE2+ washer. 

 

That F21 code indicates that you have a long drain problem (which is probably obvious since the washer won't drain). Excessive suds can cause that problem. Look for evidence of that problem. If you see excessive foam in the tub, then you will need to drastically cut back on the amount of HE (High Efficiency) detergent that you are using. You should only need about 1 tablespoon of HE detergent for each normal wash load.

 

Check the washer drain in your home. See if it is clogged. If the house drain for the washer is working, then I recommend that you examine the drain hose for the washer to see if it is kinked. Check the end of that hose for a lint clog. Make sure that the end of that hose is not stuck way down the drain stand pipe or submerged in drain water if you are using a drain sink beside the washer.

 

If you find no problems with the drain hose, then you can unplug the washer and check the large item filter in the drain pump as shown in the image below. You may find lint or foreign items in that area that would prevent the washer from draining. Note: Drain the water from the washer before removing that large item filter from the drain pump. You can manually open the washer door by removing the bottom front service panel. Carefully reach up along the inside of the front panel and pull down on the release tab that you will find at the bottom of the door latch assembly. You can then open the washer door and remove the laundry. Drain the water out using a wet/dry shop vacuum.

 

These tips may help you resolve that F21 problem in your washer. If you need more assistance, reply with additional details.

 

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services Washer Repair. 

Read More
Lyle W -
Sears Technician
March 25, 2013