Model #REF30QW(PRIOR-9708) THERMADOR Range, Electric/Gas

  • Cover
    3 Results
  • Gas Maintop Component (rdds30vqb(prior-9707)) (rdds30vrs(prior-9707)) (rdf30qb(prior-9708)) (rdf30qw(prior-9708)) (rdf30rs(prior-9707)) (rdfs30(prior-9708)) (rdss30(prior-9707))
    3 Results
  • Manifold Assembly Sequence (rdds30vqb(prior-9707)) (rdfs30(prior-9708)) (rdss30(prior-9707))
    3 Results
  • Burner Box Assembly (rdds30vqb(prior-9707)) (rdfs30(prior-9708)) (rdss30(prior-9707))
    3 Results
  • Manifold Assembly (rdf30qb(prior-9708)) (rdf30qw(prior-9708))
    3 Results
  • Burner Box Assembly (rdf30qb(prior-9708)) (rdf30qw(prior-9708))
    3 Results
  • Gas Control Valve Detail (rdds30qw(prior-9708)) (rdf30qb(prior-9708)) (rdf30qw(prior-9708)) (rdfs30(prior-9708)) (rdss30(prior-9707))
    3 Results
  • Jet Holder Assembly Detail
    3 Results
  • Free Standing Range (rdfs30(prior-9708))
    3 Results
  • Drop-in Range (rdds30vqb(prior-9707))
    3 Results
  • Slide-in Range (rdds30qw(prior-9708))
    3 Results
  • Maintop Component (red30vqb(prior-9707)) (red30vqrs(prior-9708)) (red30vqw(prior-9708)) (ref30qb(prior-9708)) (ref30qw(prior-9708)) (ref30rs(prior-9707)) (res30qb(prior-9708)) (res30rs(prior-9707)) (res30w(prior-9708))
    3 Results
  • Burner Box Assembly (ref30qb(prior-9708)) (ref30qw(prior-9708)) (res30qb(prior-9708))
    3 Results
  • Free-standing Range (ref30qb(prior-9708)) (ref30qw(prior-9708))
    3 Results
  • Drop-in Range (red30vqb(prior-9707)) (red30vqrs(prior-9708)) (red30vqw(prior-9708))
    3 Results
  • Slide-in Range (res30qb(prior-9708))
    3 Results
  • Drop-in Snorkel Assembly (rdds30vqb(prior-9707)) (rdds30vrs(prior-9707)) (red30vqb(prior-9707)) (red30vqrs(prior-9708)) (red30vqw(prior-9708))
    3 Results
  • Drop-in Base Assembly (rdds30vqb(prior-9707)) (rdds30vrs(prior-9707)) (red30vqb(prior-9707)) (red30vqrs(prior-9708)) (red30vqw(prior-9708))
    3 Results
  • Main Oven Liner And Module
    3 Results
  • Base With Toe Kick Panel (rdds30vqb(prior-9707)) (rdds30vrs(prior-9707)) (red30vqb(prior-9707)) (red30vqrs(prior-9708)) (red30vqw(prior-9708))
    3 Results
  • Storage Drawer And Base
    3 Results
  • Main Oven Door Assembly
    3 Results
  • Schematic Rdfs30q, Rdss30q-ver.1
    3 Results
  • Wiring Diagram (rdfs30q, Rdss30q)
    3 Results
  • Schematic (ref30q, Res30q)
    3 Results
  • Wiring Diagram (ref30q, Res30q)
    3 Results
  • Schematic (rdds30vq)
    3 Results
  • Wiring Diagram (rdds30vq)
    3 Results
  • Schematic (red30vq)
    3 Results
  • Wiring Diagram (red30vq)
    3 Results
  • Supplemental Instructions For S/s 30" Ranges
    3 Results
Find part by diagram >

Question and Answers

Q:

Washer Agitates Prior to Water fill.

A:

Thank you for your question.

I am sorry you are having a problem with your washer. Usually when this happens, it is because of the load sense switch. The relay in the switch sticks and allows the washer to fill and agitate at the same time. A simple check is to access the load sense switch and unplugging the wires to it. Then check the operation. I have provided you with the instructions for accessing the load sense switch below. Make sure you unplug the washer first. Once the console is open the load sense switch it the switch that has the clear plastic hose connected to it. Remove the connector that has the violet, white and the blue with orange stripe from the switch. Then carefully plug the washer back in and start a wash cycle. If the washer does not do anything, you have to replace the load sense switch. If the washer still agitates, the problem is most likely a failed timer.

Please feel free to let me know if you need further assistance.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
November 13, 2011
Q:

Washer not spinning fast enough to eject water prior to drying

A:

The procedures for replacing the drive belt in this type of washer are shown in the 4 images below. Be sure that you unplug the washer before accessing internal components. The first image shows how to remove the front panel. I recommend that you check the belt before replacing it. If it is worn and slipping, then it will need to be replaced. The other images show how replace the belt. You will need to carefully remove that drain pump to get the belt off and replace it. Be sure that you route that belt properly when replacing it.

This repair is normally completed by a technician. I recommend that you carefully review the procedures provided below. If you are not completely confident that you can properly replace that belt, I recommend that you schedule a service technician to repair the washer. Here is a link for the Sears Service website: Sears Home Services .

If you need more help, reply with additional details and we will try to assist you further.

Read More
Lyle W -
Sears Technician
March 30, 2011
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
March 30, 2011
See more answers
Q:

My twin-v snapped both connecting rods. prior to installing new ones, should the sleeve be oiled

A:

No lubricant is recommended for the sleeve or the o-ring.

Be sure you torque the nut that holds the connecting rods to the motor shaft to 85-100 foot pounds.

Read More
Jimmy K -
Sears Technician
July 18, 2008