Model #MX-80 EPSON computer/printer

  • Lower Case
    3 Results
  • Printer Mechanism
    3 Results
  • Filter Circuit Board Unit
    3 Results
  • Hmtp Circuit Board Unit
    3 Results
  • Power Cord
    3 Results
  • Mpel Circuit Board
    3 Results
  • Feed Assembly
    3 Results
  • Paper Feed Motor
    3 Results
  • Sprocket Assembly
    3 Results

Question and Answers

Q:

Treadmill belt

A:

Thank you for your question.

I am sorry you are having a problem with the treadmill. By what you have stated I suspect the walking belt needs to be adjusted. I have provided you with an image below showing how to adjust the walking belt. Before adjusting, I recommend inspecting the area of the adjusting bolts. Look at both bolts. They should be sitting on the end cap. I often see the end cap break on one side or the other if both of the adjusting bolts look the same use the instructions below to center the walking belt. If the bolt is pulled through the end cap, you will need to order and replace the end cap. The end cap can be ordered from our parts website: Sears Parts Direct .

Please let me know if you need further assistance on the repair of the treadmill.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
March 29, 2011
Q:

Kenmore Series 80

A:

If you spin the input shaft in the correct direction it should cause the agitate shaft to move. If it does not move it very well could indicate a gear case failure. NOTE: Be sure the motor coupler was not broken that links the motor to the gear case. If the motor coupler is broken it will not agitate or spin.

Read More
Joey S -
Sears Technician
July 20, 2010
Q:

Series 80 does not agitate or spin

A:

Thank you for your question.

I am sorry but we have sold the 80 series for many years and not all have the same wiring. I will give you information based on one of our newer 80 series washers. By what you have stated, it sounds like a lid switch failure. The lid has to be closed for the motor to run on your washer. If the lid switch is faulty, it will act as if the lid is not closed. On some models, make sure the lid hinge screws are tight. If the screws are loose, the hinge might not activate the lid switch. A quick check you can do is to run a cycle with the lid switch jumped. If the washer operates, the lid switch need to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the colored wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. start the washer in a cycle, and let it go. If the washer completes the cycle, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

If the motor is running but the washer will not agitate or spin, I would suspect the motor coupler.The third image shows how to replace the motor coupler.

I hope this is helpful. Please reply below with a model number and more details. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
May 27, 2011