Model #MAC CLASSIC APPLE Computer

  • Chassis And Pcb Board
    3 Results
  • Power Sweep Assembly
    3 Results
  • Logic Board Assembly
    3 Results
  • Rear Housing Assembly
    3 Results
  • Chassis Assembly
    3 Results
  • Front Bezel Crt Assembly
    3 Results
  • Fdhd Assembly
    3 Results
  • Hda Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

McCulloch MAC 160S Chainsaw

A:

Thank you for your question.

 

I am sorry you are having a problem with the chain saw. If the chain will not tighten when you loosen the nuts and turn the adjusting screw, I suspect the adjustment pin on the clutch cover is broken or not positioned in the bar. I found a video that shows how to replace the adjustment pin. The video also shows how the pin should fit into the bar. Click here to watch the video. 

 

I hope this is helpful. Please let me know if you need further assistance.

 

 

 

 

Thank you for using Manage my life.

 

Mark T.

Read More
Mark T -
Sears Technician
November 05, 2013
Q:

McCulloch Mac 2816 weed wacker

A:

Thank you for your question.

I am sorry you are having a problem with the trimmer. If you have installed a module and still do not have spark I recommend removing the kill wire and check for spark with a new plug. If you still do not have spark double check the air gap between the module and the magnet on the flywheel. The air gap should be set between .010 to .012. Then check for spark. If there still is no spark, the problem is either a weak flywheel magnet or defective module. If the magnet holds a screwdriver, it should be fine.

I hope this is helpful. Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
June 20, 2011
A:

Thank you for the reply. If the kill wire is removed from the module, when you are checking for spark it will not matter if it is frayed. You can repair the wire later once you have spark. If the magnet is fine and the air gap is set, you should have spark. If you do not have spark I suspect a defective module. I know it is not likely but everything else is fine. Just make sure you are using a know good plug and it is grounded to a clean ground when checking for spark. I hope this is helpful.

Read More
Mark T -
Sears Technician
June 21, 2011
A:

By what you have stated you have done, I suspect the module is defective. If you happen to have the old module, you might want to install it and check for spark with the kill wire disconnected. If you have spark, repair the kill wire. If you do not have spark I recommend replacing the module.

Read More
Mark T -
Sears Technician
June 22, 2011
A:

The coil has to be having a good connection to the engine block. This is important for the module to generate the spark. By everything you done so far, I suspect the problem is a defective module. I know it seems unlikely but the checks done point to the module.

Read More
Mark T -
Sears Technician
June 23, 2011
A:

We are missing something somewhere. Try to set the air gap at .012. While tightening the screws, make sure the module does not turn away from the flywheel. Then check for spark with out the spark plug. To do this, insert a screwdriver where the spark plug would go. Then hold the shank of the screwdriver about a 1/8 inch or so from the block. While holding the screwdriver in this position, turn the engine over. You should see a spark jump from the shank to the block. If you get spark the plug is causing the problem. Please let me know what you find.

Read More
Mark T -
Sears Technician
June 27, 2011
See more answers
Q:

MAC 4600 Chain Saw User Manual needed

A:

Thank you for your question.

I have searched for a manual for the chainsaw but did not have any luck. I am sorry I could not help with finding the manual. I recommend posting on manualsonline.com. The post will stay up and if any one uploads a copy, you should be alerted.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
November 30, 2011