Model #MAC 11-400056-02 MCCULLOCH Line Trimmers/Weedwackers, Gas

  • General Assembly
    3 Results
  • Engine Assembly
    3 Results
  • Carburetor Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

What is causing the error messages F 02 & F 11 on my Kenmore washer?

A:

The F02 error code indicates that the washer is taking too long to drain. This error code can also be displayed following a problem with oversudsing. Make sure that you are using HE (High Efficiency) detergent in the proper amount. The following link of a previous answer provides additional information and troubleshooting for this error code: Why do I keep getting the F02 code on my washer?

The F11 fault code indicates that you have a serial communication error between the machine control board and the motor control board. This can be caused by a loose wire harness connection between these two boards. It can also be caused by a failed machine or motor control board. The specific technical explanation is contained in this link of a previous answer:

Where can I find a repair manual to help me resolve an F11 error code on a Kenmore washer?

A service technician is needed to diagnose and repair this type of problem most of the time.

If you want to troubleshoot these failures yourself and need more technical help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
August 20, 2008
Q:

McCulloch MAC 160S Chainsaw

A:

Thank you for your question.

 

I am sorry you are having a problem with the chain saw. If the chain will not tighten when you loosen the nuts and turn the adjusting screw, I suspect the adjustment pin on the clutch cover is broken or not positioned in the bar. I found a video that shows how to replace the adjustment pin. The video also shows how the pin should fit into the bar. Click here to watch the video. 

 

I hope this is helpful. Please let me know if you need further assistance.

 

 

 

 

Thank you for using Manage my life.

 

Mark T.

Read More
Mark T -
Sears Technician
November 05, 2013
Q:

McCulloch Mac 2816 weed wacker

A:

Thank you for your question.

I am sorry you are having a problem with the trimmer. If you have installed a module and still do not have spark I recommend removing the kill wire and check for spark with a new plug. If you still do not have spark double check the air gap between the module and the magnet on the flywheel. The air gap should be set between .010 to .012. Then check for spark. If there still is no spark, the problem is either a weak flywheel magnet or defective module. If the magnet holds a screwdriver, it should be fine.

I hope this is helpful. Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
June 20, 2011
A:

Thank you for the reply. If the kill wire is removed from the module, when you are checking for spark it will not matter if it is frayed. You can repair the wire later once you have spark. If the magnet is fine and the air gap is set, you should have spark. If you do not have spark I suspect a defective module. I know it is not likely but everything else is fine. Just make sure you are using a know good plug and it is grounded to a clean ground when checking for spark. I hope this is helpful.

Read More
Mark T -
Sears Technician
June 21, 2011
A:

By what you have stated you have done, I suspect the module is defective. If you happen to have the old module, you might want to install it and check for spark with the kill wire disconnected. If you have spark, repair the kill wire. If you do not have spark I recommend replacing the module.

Read More
Mark T -
Sears Technician
June 22, 2011
A:

The coil has to be having a good connection to the engine block. This is important for the module to generate the spark. By everything you done so far, I suspect the problem is a defective module. I know it seems unlikely but the checks done point to the module.

Read More
Mark T -
Sears Technician
June 23, 2011
A:

We are missing something somewhere. Try to set the air gap at .012. While tightening the screws, make sure the module does not turn away from the flywheel. Then check for spark with out the spark plug. To do this, insert a screwdriver where the spark plug would go. Then hold the shank of the screwdriver about a 1/8 inch or so from the block. While holding the screwdriver in this position, turn the engine over. You should see a spark jump from the shank to the block. If you get spark the plug is causing the problem. Please let me know what you find.

Read More
Mark T -
Sears Technician
June 27, 2011
See more answers