Model #M-100 BLACK & DECKER walk behind lawnmower, electric

  • Replacement Parts
    3 Results

Question and Answers

Q:

90 series kenmore washer..m#110. 22922 100.... spin cycle was very slow... two loads later,, then no spin..

A:

Thank you for your question and I understand your concern. I must assume the rusted area was on the center vertical portion of the spin basket because you did not mention you had removed the basket. I say this because there is another post under the spin basket in which if it rusts, it will leak water down and on the clutch. Even if water was leaking past the rust on the spin basket it would not leak water down because of the seals in the basket drive and the seals in the tub support.

The rusted basket is not preventing the washer from spinning. The likely failure is nothing more than a worn clutch band. The clutch is what is sitting on top of the gear case. It would be worth pulling the gear case again and replacing the clutch band and then see how well it spins. The clutch band kit is part #285790.

You can order the clutch band from Sears PartsDirect

Read More
Joey S -
Sears Technician
February 09, 2011
A:

Ron: Water should not leak even if the basket was removed. If water is leaking onto the floor, the tub support tube that the basket drive and gear case shaft fits up through is rusted or you have a bad tub seal.

Read More
Joey S -
Sears Technician
February 09, 2011
See more answers
Q:

oven range opening top lid to clean

A:

We don't have specific instructions for removing the cook top from this dual fuel slide-in range. The reply that you posted on the above link that Joseph P. provided seems to indicate that the range sparks and smokes when you restore electrical power to it. I recommend that you have a service technician diagnose and repair the range based on these details. Here is a link for the Sears Service website: Sears Home Services .

I don't recommend that you restore power to the range until the problem that you describe with the sparking and smoking is properly diagnosed and repaired. I also recommend that you shut off the gas supply to the range until it is repaired.

If you want to attempt to remove the cook top, here are some guidelines that may help you with that task:

  1. Refer to the parts list diagram on the Sears PartsDirect website to view cook top components. This may help you with removing that cook top.
  2. With the range still disconnected from electrical power, remove the burner grates caps and heads.
  3. According to the parts diagram, you should then see burner skirts on top of the cook top. These may be attached to the burner tube assembly head with screws. Remove the screws from each burner if you find them. You will need to rely on your personal observation of the range along with the parts list diagram to disassemble the tops of the burners.
  4. Once you have the burner tops removed, you will probably need to pull the range out and remove screws from both sides of the range that secure the cook top to the frame. Again, you will need to rely on your personal observation of the range to find these screws.
  5. Once you remove the screws that secure the cook top to the range frame, you should be able to carefully pull up the cook top.

I hope that this information helps. If you need more assistance, reply with additional details and we will try to assist you further.

Read More
Lyle W -
Sears Technician
April 28, 2011
Q:

range does not get higher than 100 degrees

A:

Thank you for your question and I understand your concern.

Based on your symptom and details, the high limit thermal switch has likely tripped during the high heat of the self clean cycle. The thermal switch is located on the back of the range and will likely have a red wire with a white stripe and a black wire with a white stripe connected to it. You will need to remove the range and take the rear panel off in order to access the thermal switch. There will be a red reset button in the middle of the thermal switch to push and reset. There are no video or written instructions. If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

NOTE: Disconnect the range from the power supply before removing the back panel and resetting the thermal switch. I strongly suggest calling a service technician to diagnose why the thermal switch tripped.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
February 13, 2012