Model #LSR6332KQ0 WHIRLPOOL Residential Washers

  • Top And Cabinet/literature
    3 Results
  • Controls And Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
  • Miscellaneous/optional
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

top load whirlpool washer model LSR6332KQ0 doesn't drain after completing all cycles

A:

Hi Adelia,

Thank you for submitting a question to Manage My Life.

I am sorry you are having problems with your washer.

The first thing I recommend is checking the drain hoses and drain pump for clogs. Here is a video that will demonstrate gaining access to these; Video . You will need to make sure the drain pump impeller is not impinged or damaged.

Please check the things I have detailed here and report back with your findings. I am looking forward to assisting you again in the near future.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
July 12, 2011
Q:

Burning smell & oil leak LSR6332KQ0 Whirlpool Washer

A:

Thank you for your question and I understand your concern.

If the washer was laid over on its back, some oil may have leaked out of the small vent hole on top of the gear case cover.  Wipe the oil up and check it again later. If the oil spot reappears, then you will need to look and determine where it's leaking from. NOTE: It's not abnormal for some oil to begin leaking over time and use. A little oil leaking is nothing to worry about and you will not need to add any.  Also, when you installed the two plastic couplers on the motor shaft and gear case shaft, make sure the couplers were driven up flush to the end of the shafts or it can cause friction which can cause a burning odor.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

Read More
Joey S -
Sears Technician
May 09, 2013
Q:

Why does my washer just stop and make clicking noises instead of draining and continuing the cycle?

A:

Your symptoms indicate that you may have a problem with the lid switch. This could be causing the washer to stop and not drain. I recommend checking this component first. Make sure that the lid strike (Key 20 in the image below) is intact and activating the lid switch (Key 11). You should hear a slight clicking noise as the switch closes. If it is activating properly and the washer won’t drain, the next step would normally be to access the switch and place an insulated jumper wire in the disconnect plug to simulate a closed lid switch. You should only attempt this if you are completely confident that you can safely access this internal component and complete the procedure.

To access the lid switch, follow these steps:

  1. Unplug the washer to disconnect electrical power.
  2. Use a putty knife to release the clips on each side of the console that secure it to the top washer panel.
  3. Hinge the console up and back over the top of the back washer panel.
  4. Release the clips that secure the washer cabinet to the back panel (see image).
  5. Pull the washer cabinet forward to access the lid switch harness (see image). Disconnect the wire harness to the lid switch.
  6. Pull the cabinet off of the washer.

This process should give you access to the lid switch. Carefully place the insulated jumper wire in the wire harness to the timer to simulate the lid switch being closed and reassemble and test the washer. If the washer runs properly with the lid switch jumped, replacing the lid switch should fix your problem. NOTE: Do not leave the lid switch jumped. Replace the lid switch because it is an important safety feature of the washer.

If the washer still does not run to drain the water, you could have a wiring problem. With the washer unplugged, check the wiring to the motor using the wiring diagram shown below.

If these checks do not help you diagnose and repair the problem, resubmit your question with additional details for more help.

Read More
Lyle W -
Sears Technician
April 08, 2008

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show