Model #KS-706HT KENWOOD Speakers

  • Speaker
    3 Results
Find part by diagram >

Question and Answers

Q:

estate whirlpool washer

A:

Thank you for your question.

By what you have stated, it sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer to work. If the lid switch is faulty, it will fill and wash but nothing else. A quick check you can do is to jump the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the two colored wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

Please click here to watch a video on how to replace the lid switch.

I hope this is helpful. Please reply below if you need further assistance. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
July 22, 2011
Q:

Grille of the Kenmore Microwave 72180833500 Kenmore Elite Microwave - range hood

A:

That grille assembly for your microwave is part 3531W1A019A (Key 3038 on that parts diagram). Here is a direct link for that part: Grille Assembly for Kenmore Microwave Model 721.80833500 .

Unplug the microwave before installing that grille. Remove the screws from the top of the grille and pull it forward and off of the microwave. Replace it with the new grille and secure it with the screws.

I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
October 24, 2012
A:

Haibo: You will need to remove the two screws securing the microwave to the bottom of the cabinet and drop the front of the unit down or completely remove the microwave to access the screws. I added the URL address below to installation instructions where you can reverse the procedure and remove the microwave. Copy and paste the URL below in your browser. http://www.managemylife.com/mmh/installation_guides/134065/KENMORE-ELITE-Microwave-Hood-Combo-1011608L?brand_name_search=72180833500+

Read More
Joey S -
Sears Technician
August 13, 2013
See more answers
Q:

Re: Craftsman Garage Door Opener, Model: 139.53990D. Remote won't open door-sometimes. The battery is OK. What is happening?

A:

Do you have other remotes? If so do they have the same problem? Try putting a different remote in your vehicle and the next time your remote doesn't work, try the second remote. If the second remote doesn't work, there is probably a problem with intermittent radio frequency (rf) in the area. If the second remote works ok something is wrong with the remote in your vehicle.

The Sears technicians have a tester for locating the source of rf signal.

Read More
Jimmy K -
Sears Technician