Model #JGR8875QDS JENN-AIR Free Standing, Gas

  • Control Panel/top Assembly
    3 Results
  • Cabinet
    3 Results
  • Cavity
    3 Results
  • Gas Controls
    3 Results
  • Door/drawer (stl)
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers


Oven won't light JGR8875QDS


Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Jenn-Air oven.

From the information you have provided above, I can understand the frustration of having your oven malfunction, after researching model number JGR8875QDS. It could be a couple of parts to cause this issue. the first would be the bake ignitor. The oven doesn’t seem to be getting the spark to ignite. Another part is the bake burner. These two parts are what cause the oven to heat since all else works fine the issue is between these parts. The part# for the ignitor is 7432P136-60. The part# for the burner is 31945701.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting*

Read More
Benny23 -
Sears Technician
May 04, 2015

How hard is it to install a main control board myself? JGR8875QDS Jenn-air Jenn air cooking


Thank you for choosing and being a valued member. I can certainly assist you in locating the isntructions to replace the control board on your range. 

Front Control Panel
1. Open or remove oven door from unit.
2. Remove control knobs from gas valves, by pulling.
3. Remove screws securing front control panel, located
on the bottom edge of the front control panel.
4. Remove control panel by sliding one way or the other
and pulling away from the unit.
5. Reverse procedure to reassemble.

Maintop Assembly
1. Turn power off to unit.
2. Remove front control panel, see "Front Control Panel"
3. Remove grates and caps.
4. Remove screws securing top surface burner to
5. Lift surface burner off.
6. Raise the front edge of the maintop and pull forward.
7. Lift maintop assembly from the oven chassis.
8. Reverse procedure to reinstall maintop assembly.

Control Panel
1. Remove maintop assembly, see "Maintop Assembly"
procedure, steps 1 through 7.
2. Remove screws securing control panel heat shield.
3. Remove screws securing bottom outside edges of the
control panel.
4. Pull unit out from the wall far enough to allow the
back outside screws to be loosened.
5. Loosen the back outside screws securing control
panel to backguard.
6. Grasp front lower outside edges of the control panel
and push inward on the outside edges of the
backguard to release the control panel front.
NOTE: Front edges of the control panel are difficult to
release from backguard.
7. Once the control panel bottom edges are free, pull
control panel forward and raise the control panel
upward to release screws securing top back edges
and allow control panel to tip forward.
8. Reverse procedure to reinstall control panel.

Control Board Assembly
1. Remove control panel, see “Control Panel”
procedure, steps 1 through 6.
2. Remove screws securing control board bracket to
control panel.
3. Label and disconnect terminal plug from control
board assembly.
4. Reverse procedure to reinstall control board

You can also visit for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
December 18, 2014

JennAir Gas Range Model #JGR8875QDS Control Panel vs. Control Assembly JGR8875QDS


Thank you for choosing sears I would happy to help you with your range. Upon researching model JGR8875QDS; the control board is the part that controls the oven. The control panel is the face that goes over the control board and it communicates what action needs to be taken to the control board according to the button you press on the control panel. The parts are separate but they work together. I have posted a link below of the control board key#2 and control panel key#1.

I trust that this information will help you, thank you have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
October 10, 2014

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show