Model #GHW9150PW4 WHIRLPOOL Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Pump And Motor Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Whirlpool Washer GHW9150PW4 starts filling up with water after cycle is complete

A:

Thank you for your question and I understand your concern.

I assume the washer is filling with water while the washer is not in use. If this is the case, the water inlet valve on the back of the washer is likely not shutting completely off and is slowly filling the washer when not in use. Removing and replacing the water inlet valve will most likely resolve the issue. In the meantime, I suggest shutting the hot and cold water supply off to the washer until the water inlet valve is replace.

The water inlet valve for Whirlpool washer model GHW9150PW4 is part #8182862 which can be ordered from Searspartsdirect. 

In order to access and replace the water inlet valve, the top of the washer must be removed. NOTE: Disconnect the power cord and shut the hot and cold water off before servicing. 

You will need to remove the hot and cold fill hoses and then remove the screws on the back of the top. Once the screws have been taking out on the back of the top, slide the top back a few inches and then lift it up and off. The water valve is secured with a couple of screws. You will need to squeeze the two hose clamps and slide then back and remove the two hoses from the water inlet valve as well as the hot and cold fill hoses. Disconnect the two wire connections and make sure you re-connect the two wire connections on the same terminals on the new valve.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 

Read More
Joey S -
Sears Technician
November 22, 2013
Q:

Control lock light is keeping me from using my Whirlpool Duet washer. How do I disable the light?

A:

Hi Dino,

Thank you for submitting a question to Manage My Life. I know how frustrating it can be when appliances do not function properly.

If you tried the procedure detailed in the Owners' manual (see below) and it did not respond, then most likely you have a faulty user interface (part number 8182785). It is possible that the button for the end of cycle signal is stuck. I am including instructions below for disassembling your console so you can check it.Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

To lock the controls Select and hold END OF CYCLE SIGNAL for 3 seconds. The CONTROL LOCKED status light glows. To unlock the controls Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Thanks again for using Manage My Life.

Landell

Read More
Landell -
Sears Technician
September 27, 2011
A:

Hi Dino, That is not a known error code. You did not mention the part number on the user interface you installed. Here is what I need you to do; 1. Double check the model number on the washer. 2. Look for a part number on the new user interface. 3. Look for a part number on the main control board. 4. Check the wiring between the main control and the user interface. Check the things I have listed above and report back with your findings. Thanks again for using Manage My Life. Landell

Read More
Landell -
Sears Technician
October 04, 2011
A:

Hi Dino, Sometimes in the appliance repair world we are forced to use the process of elimination. At this point the main control (part number 8182695) is the likely suspect. Thanks again for using Manage My Life. Landell

Read More
Landell -
Sears Technician
October 04, 2011
A:

Dino, Glad to hear you are up and running. Please keep Manage My Life in mind for all of your do-it-yourself projects. Landell

Read More
Landell -
Sears Technician
October 31, 2011
See more answers
Q:

washing machine trouble

A:

Hi Alan,

Thank you for submitting a question to Manage My Life.

If you are unable to unlock the control on your washer by pressing and holding the END OF CYCLE signal button for 3 seconds, you will most likely need to replace the user interface (part number 8182785). You can try unplugging your washer and when you plug it back in, the control lock may be off.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram or to purchase any parts needed; Sears Parts Direct .

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance, include more details in a reply to this post.

Landell

Read More
Landell -
Sears Technician
December 30, 2011
A:

Hi Alan, Glad to hear you are up and running. Please keep Manage My Life in mind for all of your do-it-yourself projects. Landell

Read More
Landell -
Sears Technician
January 03, 2012
A:

Dustin

You can unlock the door by removing the toe panel and reaching up along the inside of the front and manually unlocking the door latch. I am including a set of images below that demonstrates this procedure. Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

If the door latch/lock is damaged you will need to replace it.

I hope this is helpful. If I may be of further assistance please include more details in a reply to this post.

Landell

Read More
Landell -
Sears Technician
July 10, 2012
See more answers

Top Parts