Model #EH-1930 RYOBI Drill Driver

  • Impact Drill
    3 Results
  • Crankshaft And Piston System
    3 Results
  • Flywheel Magneto System
    3 Results
  • Crankcase System
    3 Results
  • Cylinder And Cover System
    3 Results
  • Carburetor System
    3 Results
  • Recoil Starter System
    3 Results
  • Fuel Tank System
    3 Results
  • Air Cleaner System
    3 Results
  • Muffler System
    3 Results
Find part by diagram >

Question and Answers

Q:

i order a eh mahogany fire place

A:

Researching for manual.

I will research for this information and get back to you.

Update on manual. I have recieved the manual for your fire place and will e-mail it to you.

Sam A.

Read More
Sam A -
Sears Technician
November 16, 2011
A:

Thank you, Michael, for your request for the fireplace manual. I will need for you to send me your e-mail address to my Sears e-mail account so it will not be on the public domain. I will be happy to send it to you. sande38@searshc.com Sam A.

Read More
Sam A -
Sears Technician
November 19, 2011
See more answers
Q:

Where kind I find information, parts, manuals, etc. for a late 1930'/early 1940's model Frigidaire refrigerator?

A:

I recommend contacting Frigidaire at Frigidaire.com or by calling them at 1-800-374-4432. We would not have any information on a Frigidaire refrigerator dating back that far.

Read More
Joey S -
Sears Technician
May 13, 2010
Q:

Kenmore Elite He3T cycle flashing wont start?

A:

Hi Joel,

Thank you for submitting a question to Manage My Life.

From your description this is likely a bad door switch/lock. The first thing you will need to do is test the door lock. I am including the diagnostics and lock/door switch testing information below. The diagnosis of this issue will require the use of an ohm/volt meter and you will have to perform ohm checks and/or live voltage checks. If you have an ohm/volt meter and are confident in your technical abilities, please utilize the checks below. Live voltage checks are dangerous, and possibly deadly. Exercise caution at all times. If you are not comfortable working with live electricity I suggest you call an experienced service technician.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Landell

Read More
Landell -
Sears Technician
November 01, 2011
A:

Joel, From your description, you most likely have a failed door lock assembly (part number 8182634). I would recommend replacing that first. I am including a link to this part below. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. Landell

Read More
Landell -
Sears Technician
November 06, 2011
A:

Hi Joel, Sometimes in the appliance repair arena we are forced to play the process of elimination game. Normally these machines are quick to give an error. The Fdl is typical for door lock or control issues. As far as replacing just the relay, I cannot advise you to replace anything other than the CCU (Central Control Unit) (part number 285924). I would however strongly urge you to ohm the wire harness between the CCU and door lock assembly. Landell

Read More
Landell -
Sears Technician
November 09, 2011
A:

Joel, Ohming the wires simply proves that there are not any defects in the wiring. Now from what you have told me I am comfortable advising you that the control should be replaced. Landell

Read More
Landell -
Sears Technician
November 09, 2011
A:

Joel, Lock is DL3-1 to DL3-2 and unlock is DL3-2 to DL3-3. I am including a wiring diagram below. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. Landell

Read More
Landell -
Sears Technician
November 13, 2011
A:

Hi Joel, Thanks for the video. There are 2 things I want you to try. First, push in on the door at the door lock while you start a cycle. If the door locks and the washer starts (clicking loop goes away) then you will need to examine the door boot (bellows) and/or the door and hinges. The locking mechanism may be in a bind. The next thing you will need to check is incoming voltage at IF2 (green connector in the image below). When you start a cycle the voltage should be 120vac, if it drops you are loosing voltage into the washer. I hope this is helpful. Check the things I have covered here, and if I may be of further assistance, include more details, in a reply to this post. Landell

Read More
Landell -
Sears Technician
November 15, 2011
See more answers