Model #D130-04 TYPE 2 DEWALT Drill Driver

  • Unit Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

riding mower will turn but wo'nt start changed spark pluges

A:

Thank you for your question.

I am sorry you are having a problem with the tractor.

There are three basics the engine needs: Ignition, Compression, and Fuel. The specifics can vary from model to model, and your Manage My Home profile did not list what model this might be, but there are some quick checks you can do to see if you have these three basics. I am assuming from your question that this is a engine with a good battery and that it is just turning over and not firing at all, but even if that is not the case these basic checks can still help narrow down the source of the problem. First, go back to the spark plug. Remove the leads, or wires, that connect from the engine to the plug. Remove the plug and put them back in the leads. Now position the leads so the metal end of the plug is against the engine or another clean unpainted metal ground point. Keep your hands away from the plugs so you do not get shocked, and turn the key to the start position. Look for sparks at the ends of the Spark Plug. Look carefully as they might be hard to see in sunlight or other bright lights. If there is spark there then you have ignition, the first of the three basics. If not, you likely have an electrical problem that needs to be traced. The engine should have been spinning over faster once the plug was removed and you should hear air rushing out of the spark plug holes in puffs. You could even try putting a thumb or finger over each plughole to see if the pressure pushes your finger off when turning over, just be careful not to touch the grounded plugs so you do not get shocked. If that all happens then you have the second ingredient, compression. If not then you may need a valve adjustment or may have a broken component inside the engine. That leaves fuel. Check the tips of the plug you just removed, if fuel is reaching the engine there should be some residue there and they should look somewhat wet. If you used your finger to check compression then you may even see some residue on your finger. If there is fuel here, your problem may be old fuel or a timing issue. Try putting a small amount of good fuel into the throat of the carburetor and turn the key to start. If your problem is fuel related only, the engine should now try to start, or even run, until the fuel you put in is gone. That would indicate the fuel supply is being stopped in the fuel tank, fuel line, fuel filter, fuel pump, or carburetor. Some carburetors have a solenoid to stop the fuel supply when the key is off and a malfunction there could also be the problem. I hope this is helpful.

If you need further assistance, please reply with a model number and more details.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
September 06, 2011
Q:

Any one with the same problem with samsung washing machine WF448AAP/XAA 04

A:

I researched that part. The bottom portion of that dispenser housing is only available as a complete dispenser housing assembly (part DC97-14522A). Here is a direct link for that part: Dispenser Housing for Samsung Washer WF448AAP/XAA 04 .

Read More
Lyle W -
Sears Technician
March 24, 2012
A:

Let us know if that part fits properly if you get the chance. Let us know if you need more help.

Read More
Lyle W -
Sears Technician
March 26, 2012
See more answers
Q:

What type oil is used in a Craftsman rear tine tiller engine and gear box? There are 2 oil plugs.

A:

Both oil plugs are for the engine. Engines that are used in tillers are used for a number of applications. The oil plugs are placed in more than one place on the engine so if one plug is not accessible the other will be.

The engine uses 30 weight motor oil. The transmission on your tiller doesn't have oil in it. It has axle grease and never needs changing.

Read More
Jimmy K -
Sears Technician