Model #9G902-0145-D1 Briggs & Stratton engine

  • Engine
    3 Results
  • Carburetor/tank
    3 Results
  • Starter/flywheel
    3 Results

Question and Answers

Q:

Why does my Whirlpool dishwasher GU2500XTPQ3 show the code "d1" when I run the diagnostics check?

A:

You did indeed use the correct “key dance� for the service diagnostics cycle. The d1 you are seeing is not an error code; it signifies that the diagnostic cycle has been started. D1 is the control board platform used in this dishwasher. The blinking clean light does typically indicate a heater circuit fault (heating element, high limit thermostat, door switch, wiring, or control board).

This is a very labor intensive do it yourself project, if you are not completely confident in your repair skills, I recommend calling a service company to diagnose and repair your appliance. If you have a volt/ohm meter and are comfortable working around live electricity I can give you a few checks that will help you diagnose the problem. If you are not already sure you can perform these checks safely and competently, refer this work to a qualified professional. Working with live electrical current can be very hazardous and possibly deadly. Testing voltage output requires working with electrical current. Do not attempt these measurements without the proper tools and safeguards.

Begin by checking VAC (Voltage Alternating Current) at the terminal block, the terminal block is behind the toe panel under the dishwasher. It should be 120 volts. I have put together a “tech sheet� that includes disassembly and some testing information (see images below).

Ohm the heating circuit; with the power disconnected find P6 (white wire with a red stripe) on the control board. With your meter set to read ohms, place your red meter lead on P6 and your black lead on the neutral side (white wire with a violet stripe) of the door switch.

  • It should read 10 to 30 ohms, if not the wires could be “openâ€� or the heating element is bad and needs to be replaced.
  • If you ohmed this from the control board to the negative side door switch and you get 10 to 30 ohms the heater circuit is good and the control needs to be replaced.

If you require further assistance please resubmit question with details of the checks you have made. I will be looking forward to helping you again in the near future.

Read More
Landell -
Sears Technician
February 22, 2010
Q:

How do you replace a primer bulb on a Craftsman leaf blower? It is a model 258-798980, serial 95219N 0145.

A:

You will need to remove the screws holding the 2 outside covers on the blower. You might have to separate the 2 halves of the handle as well.

The primer bulb mounts in the outside cover and 2 fuel lines attach to it.

This is a fairly difficult job and will take some time. As you separate the covers on the blower make note of how some fuel lines and wiring are routed so you can get it assembled correctly when the primer bulb is replaced.

Read More
Jimmy K -
Sears Technician
November 16, 2009
Q:

lawn tractor

A:

Thank you for your question.

I am sorry you are having a problem with the carburetor kit. I have looked up the model number you have submitted. The carburetor kit for the engine is part number 694056 and can be ordered from our parts website: Sears Parts Direct . This kit will work on all of the carburetors that are of this style.

Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
September 08, 2011
A:

Thank you for your question.

I am sorry you are having a problem with the carburetor kit. I have looked up the model number you have submitted. The carburetor kit for the engine is part number 694056 and can be ordered from our parts website: Sears Parts Direct . This kit will work on all of the carburetors that are of this style.

Please let me know if you need further assistance.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
September 08, 2011
See more answers