Model #95-2187-57-06 TAPPAN Top-Mount Refrigerator

  • Cover Page
    3 Results
  • Door Section
    3 Results
  • Shelves, Controls, Divider, Mullion
    3 Results
  • Cabinet W/fan Assembly
    3 Results
  • Cooling System
    3 Results
Find part by diagram >

Question and Answers

Q:

Snow blade for '06 DYT4000?

A:

Thank you for your question.

I will be happy to assist you. I searched through our fit up books. The only model snow blade I show for your tractor is model 486.24441. The models you listed for older tractors with different frames.

I hope this is helpful. Please let me know if you need further assistance on the air compressor.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
December 06, 2012
Q:

917,377130 part 57 bag frames comes in two parts

A:

Thank you for your question.

There are two types of bags. The first has a pocket that the back section of the frame threads. To install this style you have to thread the back section through the pocket. Then bunch up the bag so the ends of the frame are sticking out on each side. Now take the front part of the frame and slip it on to the back part of the frame. Most of the time, these will not line up because one of them is bent. If this is the case, flex the back section to match the front. Once you have them joined, work the bag into position along each side. Then work the vinyl binding over the frame opening.

The second style does not have the pocket. This style you have to slip both parts of the frame together first. Again, you might have to flex the parts to get then to fit. Once it is together put the bag over the frame and secure with the vinyl bindings.

I hope this is helpful. If you need further assistance, please reply below.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
September 19, 2011
A:

Thank you for your question.

There are two types of bags. The first has a pocket that the back section of the frame threads. To install this style you have to thread the back section through the pocket. Then bunch up the bag so the ends of the frame are sticking out on each side. Now take the front part of the frame and slip it on to the back part of the frame. Most of the time, these will not line up because one of them is bent. If this is the case, flex the back section to match the front. Once you have them joined, work the bag into position along each side. Then work the vinyl binding over the frame opening.

The second style does not have the pocket. This style you have to slip both parts of the frame together first. Again, you might have to flex the parts to get then to fit. Once it is together put the bag over the frame and secure with the vinyl bindings.

I hope this is helpful. If you need further assistance, please reply below.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
September 19, 2011
A:

I am sorry that was not helpful. I checked the instructions posted in the manual. I posted the instructions for you model below. Click on the image to enlarge it. If your model differs, please reply below. If you could include a picture of the bagger and frame it would be helpful.

Read More
Mark T -
Sears Technician
September 19, 2011
See more answers
Q:

Manual help...How do I install a lever for my Craftsman 247-884551 snowblower? The manual has a pick, but doesn't show close up of where it goes. Thank you.

A:

Thank you for your question.

I have checked our manual and was not able to find an image of how the spring fits into the housing. I will do the best I can to explain how to install the spring. To install the spring the housing has to be taken apart and the spring is used to hold the lever in the selected gear. It should fit between the lever and the housing. You should see wear marks where the old spring was.

I hope this is helpful.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
January 11, 2011