Model #91141065791 Kenmore built-in oven, electric

  • Control
    3 Results
  • Body
    3 Results
  • Door
    3 Results
  • Wiring Components
    3 Results
  • Door Lock
    3 Results

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

f 3 error on kenmore oven model 91141065791

A:

As noted in the above link provided by Joseph P. in the first response, the F3 code indicates that you have a problem with the oven temperature sensor circuit. This is often caused by a bad oven temperature sensor.

You can shut off the circuit breaker to the oven and access the sensor probe as shown in the first image below. Measure the resistance through this component using a volt/ohm meter. You should measure near 1100 ohms of resistance through the sensor at room temperature. If the resistance is way off, then the sensor will need to be replaced. You can order a new sensor from the Sears PartsDirect website. The part number for the sensor is WB23T10002. Here is a direct link for that part: Sensor assembly .

If the sensor is okay, you could have a problem with the wire harness or the control board. You can pull the oven out of the cabinet to check the wire harness between the sensor and the control board (with the circuit breaker still shut off ). If you find no pinched or damaged wires, you can check the connection of the sensor circuit on the control board. Remove the top cover over the control compartment to access the control board (with the circuit breaker still shut off). The second image below shows the connections of the sensor circuit to the control board. With the sensor plugged back into the wire harness, you can check the resistance through the entire sensor circuit from the wires that connect to the control board. If the resistance through the sensor circuit is normal (around 1100 ohms), then you will likely need to replace the control board to fix this problem. If the resistance through the circuit is different than the reading directly at the sensor, then you apparently have a wire harness problem that is causing this failure.

These tips should help you resolve this F3 error code problem. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 19, 2010
Q:

Broiler Element Not Working

A:

Thank you for your question as to why the broil element is not working and there is no voltage at the element wires.

You should have 120 volts to the element to neutral from the L2 side of the line. This should be always there if the oven is plugged in. The L1 in on the control board supplies the other 120 volt source when you choose the broil mode it should connect to the other side of the broil element.

It is possible that the K3 relay is not closing on the electronic control board/clock. If this is the case then the control board would need to be replaced.

I hope this will help you.

Sam A.

Read More
Sam A -
Sears Technician
November 12, 2011
Q:

Kenmore Wall Oven error codes F3, F4, F5

A:

Those links for previous answers that Pvalde2 posted in the above response may help you with this failure. Those codes are normally caused by a problem with the oven temperature sensor probe. I recommend that you shut off the house circuit breakers for the oven and check that component first. You can access that component as shown in the image below. You can test it using the information in this video: Oven Sensor Testing . The sensor should measure around 1100 ohms at room temperature. If it is bad, it will need to be replaced. You can order that part from the Sears PartsDirect website. The part number is WB23T10002. Here is a direct link for that part: Sensor Assembly .

If that sensor is okay, then you could have a problem with that wiring harness or a bad clock control board in the console of the range. Reply with additional details if you need more help with this failure.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
November 02, 2011
A:

That sensor probably was bad. It is a good sign that the oven initially heated properly to 350 degrees. You likely have a problem with the wire harness connection on that sensor probe or there is a possibility that you have a bad clock control board in the consol of that oven. You can SHUT OFF THE CIRCUIT BREAKER for the oven to disconnect electrical power and check that wire harness connection at the back of the sensor probe. If you are able to access the clock control board in the console, you can check the resistance of the entire sensor circuit from the connection on that control board. I provided a wiring diagram for that oven in the image below. That sensor circuit connects to the control board through white wires. If you measure the resistance through that circuit with the sensor plugged in and it is not around 1100 ohms at room temperature, then you probably have a bad wiring harness. The most suspect portion of that wiring harness is the disconnect plug at the back of the oven temperature sensor probe. You may be able to fix your problem by cutting that disconnect plug out of the circuit then stripping the wires and connecting them properly together using ceramic wire nuts. If that resistance through the sensor circuit is normal, then you will probably need to replace that clock control board. I hope that these additional tips help. If you need more assistance, let us know. NOTE: Be sure that you shut off the house circuit breaker for the oven before accessing internal components.

Read More
Lyle W -
Sears Technician
November 08, 2011
A:

The part number for that clock control board is WB27K5273. That clock control board is no longer available as a replacement part. You would need to send that control board into a repair center to have it fixed. The cost for repairing that control board would be around $150. Core Centric Solutions is the company that is set up to repair that control board. I provided a link for that company below this response. You can use the contact information from that website to arrange the repair of that control board if you decide to fix the oven instead of replacing it. Be sure that you shut off the house circuit breaker for the oven before removing that control board. NOTE: Based on the age of that oven and the availability of replacement parts, I recommend that you seriously consider replacing it instead of completing this repair. You can view current oven models on the Sears.com website. Let me know if you need more help.

Read More
Lyle W -
Sears Technician
November 08, 2011
See more answers