Model #831246230 Proform treadmill

  • Walking Belt
    3 Results
  • Motor/hood
    3 Results
  • Uprights/incline Motor
    3 Results
  • Console/handrails
    3 Results

Question and Answers

Q:

I need a wiring schematic foe a Proform 375 E treadmill not a user manual.

A:

Hello Neil. The image below shows the wiring schematic for the Proform 375E treadmill model 831.246230. Be sure that you unplug the treadmill before accessing internal components.

You can order parts from this page: Proform 375E Treadmill Model 831.246230 Parts .

If you get to the point where you need to have a service technician examine and repair the treadmill, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
June 09, 2012
A:

Here is the information on the consoles (4 pages).

Read More
Lyle W -
Sears Technician
June 09, 2012
A:

Here is the last page of console information.

Read More
Lyle W -
Sears Technician
June 09, 2012
A:

Here is the technical information on the controller.

Read More
Lyle W -
Sears Technician
June 09, 2012
A:

Here is a troubleshooting flow chart that may help you. If you need more assistance, let me know. Thanks.

Read More
Lyle W -
Sears Technician
June 09, 2012
A:

We are always glad to assist you. I know that I provided a large amount of technical information about that treadmill. If you need more help diagnosing your problem, reply with additional details and we will try to help you focus on the tests and troubleshooting steps that will fix the failure.

Read More
Lyle W -
Sears Technician
June 11, 2012
A:

I understand your frustration with the diagnosis of this problem Neil. Based on your description, you could have a problem with the start button or with the safety key circuit. You should be able to test that start button to see if the console detects that the button itself is working properly. That will not verify that it is sending the signal to the controller properly. I don't have the internal component wiring schematic for the console or the information on the start signal going to the controller. If you have not tested the button, I recommend that you test that start button first. Make sure that the safety key is positioned properly. If you still have problems, then you will probably need to replace that control console. I hope that this advice helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
June 15, 2012
A:

I understand your frustration with the diagnosis of this problem Neil. Based on your description, you could have a problem with the start button or with the safety key circuit. You should be able to test that start button to see if the console detects that the button itself is working properly. That will not verify that it is sending the signal to the controller properly. I don't have the internal component wiring schematic for the console or the information on the start signal going to the controller. If you have not tested the button, I recommend that you test that start button first. Make sure that the safety key is positioned properly. If you still have problems, then you will probably need to replace that control console. I hope that this advice helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
June 15, 2012
A:

The blue (PWM) to black (GND) should send a square wave DC voltage signal to the controller to indicate that the start button was pushed and the speed that is set. That signal will be difficult to measure with a volt/ohm meter. If you have a sensitive and precise meter, you may detect a slight chance in DC voltage when the start button is pressed. You can try checking that. That is the most information that I have regarding the console and control on that treadmill. I hope that it helps.

Read More
Lyle W -
Sears Technician
June 15, 2012
A:

The blue (PWM) to black (GND) should send a square wave DC voltage signal to the controller to indicate that the start button was pushed and the speed that is set. That signal will be difficult to measure with a volt/ohm meter. If you have a sensitive and precise meter, you may detect a slight chance in DC voltage when the start button is pressed. You can try checking that. That is the most information that I have regarding the console and control on that treadmill. I hope that it helps.

Read More
Lyle W -
Sears Technician
June 15, 2012
See more answers
Q:

Proform crosswald 375e model 831246230, right upper body arm came off

A:

Thank you for your question.

I see that Wade has already answered your question. if you need further assistance please reply below with additional details.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
March 24, 2011

Recommended maintenance parts & accessories

Show 3 more
No more item to show