Model #82JA-2K MAGIC CHEF Range (gas)

  • Body
    3 Results
Find part by diagram >

Question and Answers

Q:

Aloha, i own a kenmore elite electric dryer model # 110.82824181. the heater doesn't work but the motor does.

A:

Before you order that control board, I recommend that you check the house circuit breakers for the dryer. The dryer motor will run if only the L1 leg of voltage (traced in black and bright red on the wiring diagram below) is supplied to the dryer. If that second 120 volt leg of power (L2 traced in dark red below) is missing, then the dryer will not heat. If you find no problems with the breakers, then I recommend that you carefully check the electrical outlet voltage as shown in this brief repair video Video: Perform a Voltage Check on a 240 Volt Outlet .

If the outlet voltage is okay, then I recommend that you unplug the dryer and pull the black and red wires off of the electronic control board in the dryer. Tape those wires together with electrical tape for a brief test. Start the dryer in a heated cycle and see if the heating element works. If it does, then this indicates that the wiring and the rest of the components in that heating circuit are okay. The apparent cause of your problem is the heater relay on that control board and you will need to replace that part 3978917. Do not continue to run the dryer with that relay bypassed . Restore the original wiring configuration immediately following that brief test.

If the element does not heat, then you can check the heating element, the high limit thermostat and the thermal cut-off fuse in that circuit for continuity using a volt/ohm meter. Let us know if you need help testing those components.

I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
February 05, 2013
A:

Here is the wiring diagram image.

Read More
Lyle W -
Sears Technician
February 05, 2013
A:

Your details seem to indicate that you have a bad heater relay on that control board. If the heater works when you bypass that relay but will not heat when connected normally to the heater relay leads on the control board, then that control board will need to be replaced. Be sure that you unplug the dryer when accessing internal components. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
February 10, 2013
A:

Thanks Ben. I appreciate you posting that advice about replacing the relay on the control board. That is a much less expensive way to complete that repair for those who are confident in completing that procedure. The manufacturer that produces that dryer normally recommends against control board component repair. Some manufacturers do provide that information and we are glad to offer it when possible. Thanks again. Lyle

Read More
Lyle W -
Sears Technician
February 11, 2013
A:

I don't have component information for that heater relay on the control board. The manufacturer normally does not recommend replacing control board components.

Read More
Lyle W -
Sears Technician
June 11, 2013
See more answers
Q:

Bosch shi55a05 controller board SHI66A05 FD8404 00046

A:

Thank you for your question and I understand your concern.

To start with, you provided two different model numbers. Also the last two digits at the end of the model number is the revision number which is very important to have when ordering parts or you will not get the correct part for the model and revision.  Before I can confirm the correct part number of the control board I will need to have the correct model and serial number copied from the model and serial number tag.

Now,  Occasionally dishwashers will run for hours, not finish washing & show a "1" in the display. This means the module has timed out due to an unidentified heating problem -- all heating related parts must be checked until the problem is found. IMPORTANT: Whenever a “1” shows in the module display, the module must be reset (after the heating problem has been fixed) by running the dishwasher. The module resets after the 1st run.

Based on your failure, I suspect it is likely it may be related to the heater. The heater resistance cannot be measured from the control because of the flow switch. The resistance must be measured across the heating element. The heating element should measure approximately 11 Ohms. I added an image below that may be helpful. If you follow the burnt wire connection to the component using the information below may lead you to the faulty component.

So that’s what I can tell you at this point. I can give you more detailed help if you could provide me with the complete model number and the serial number. 

Read More
Joey S -
Sears Technician
October 03, 2013