Model #79096129409 KENMORE Free Standing, Electric

  • Backguard
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
Find part by diagram >

Question and Answers


F10 code when baking 79096129409 Kenmore Electric range


Thank you for choosing Sears Parts Direct. I can certainly understand how frustrating it can be when your range displays an error code. I did look into the model number you have provided and I have found that the F10 error code indicates a runaway oven temperature. The only way to reset the range, is to disconnect it from the outlet or go to the main circuit breaker of the home and switch it off for 20-30 minutes, then restore the power. If disconnecting the power for a few minutes does not help, the EOC (electronic oven control) may need to be replaced.

Follow these steps to replace the EOC:

Unplug the range.

Remove the rear access panel from the console.

Write down the wiring locations, or a digital camera may come in handy for this.

Remove the wiring being careful not to pull on the wires - pull on the lugs.

Remove the mounting screws that hold the control board in place.

The new board may not come with the overlay (this is the plastic piece the covers the front of the board with all the printing on it. This can be reused. Carefully remove the overlay and place it on the new board.

Install new control board using care not to handle the board components as much as possible.

Reconnect all wiring.

Reinstall back panel.

Let me know if this helps.

You can also visit for parts, diagrams, and repair information.
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here Let is a link for the website: Sears Home Services.

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
May 01, 2014

My bake element will not heat. Broil and top work fine. I replaced the bake element? What else can I do to get it to work? 79096129409 Kenmore Electric range


Thank you for your question. I'm sorry you are having this problem with the oven. Based on the information listed, this leads to a defective control # 316557118 and it will need to be replaced. It's available at Sears PartsDirect. If you would like more assistance, reply to this thread and I will be glad to assist you further.  

Read More
Scott D -
Sears Technician
October 01, 2013

find out how to do the oven clean on my Kenmore electric oven It is app. seen years old flat surface (ceramic elements) does not have model number how do I


Thank you for your question. This model number came in

with your question 790.96129409. I do have instructions for yjis model. Instruction as follows. A Self-Cleaning oven cleans itself with high temperatures (well above cooking
temperatures) which eliminate soils completely or reduces them to a fine powdered ash you can wipe away with a damp cloth.Prior to setting the Self-Clean cycle, any spills remaining on the oven bottom should be removed. Some models have an exposed Bake element in the lower oven cavity. On these models the bake element is designed to be tilted up using your hand
from the front of the bake element This will allow easier
access to the oven bottom for cleaning. Be careful not to raise the element more than 4 or 5 inches from the resting position. Clean any soil from the oven frame, the door liner outside the oven door gasket and the small area at the front center of the oven bottom. These
areas heat sufficiently to burn soil on. Clean with soap and water. Starting the Select Self=Clean Cycle or a Delayed Start Self=Clean Cycle. For satisfactory results, use a 2 hour Self-Clean cycle for light soils and a 3 hour cycle for average or a 4 hour cycle for
heavy soils. NOTE: The kitchen area should be well ventilated using an open window, ventitlation fan or exhaust hood during the 1st Self-Clean cycle. This will help eliminate the normal odors associated with the 1st Self-Clean cycle.

To Set the Controls for a Self-Clean Cycle or a Delayed Start Self=Clean Cycle:
(Note: If you do not want to start a Delayed Self-Clean Cycle, skips steps 2 & 3.)
1. Be sure the clock shows the correct time of day.
2. Press _. The " : " in the time of day will flash.
3. Press and hold the A pad to scroll to the time to start the delayed Self-Clean cycle. Release the pad when the
desired time is displayed.
4. Press @. " "appears in the display.
5. Press the A or V once. "3:00" appears in the display for a 3 hour cycle. To change to a 2 hour cycle press V.
"2:00" appears in the display or to select a 4 hour cycle press _. "4:00" appears in the display.
As soon as the controls are set, the motor driven lock will begin to close automatically and the "LOCK" indicator light will flash. DO NOT open the oven door while the light is flashing (it takes about 15 seconds for the oven door to lock). "CLn" will appear in the display during the Self-Clean cycle and the "LOCK" light will glow until the Self-Cleaning cycle is complete or cancelled and the oven temperature has cooled. When the Self-Clean Cycle is Completed:
2. Once the oven has cooled down for about l HOUR and the "LOCK" light has gone out, the oven door can be opened.
3. If "End" is in the display and the Select Clean indicator light remains ON, press _. The time of day will appear in the display.

Read More
dtova00 -
Sears Technician
September 15, 2013

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show