Model #79075863301 Kenmore free standing, gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Schematic
    3 Results
  • Wiring Diagram
    3 Results

Question and Answers

Q:

oven will not light

A:

Thank you for your question and I understand your concern.

You will need to remove the oven floor and determine if the glow bar bake igniter is glowing red or not. If it glows red and the bake burner is not igniting, the glow bar igniter is going to need to be replaced. If the igniter will not glow, the bake igniter could be broken or it could have a faulty electronic oven control or a faulty oven safety valve.

The oven floor can be removed by taking the two screws out located at the back of the oven floor.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
December 29, 2012
Q:

installation instructions for blackout door of kenmore range

A:

You will need the foil (parts 316102208 and 316102205) for that outer door glass. The new glass should not be installed without that foil in place. I posted the parts diagram for that door in the image below. After removing the oven door from the range and placing it on a padded surface, you will need to remove the screws (Key 10) that secure the door handle to the outer panel. You can then remove the screws (Key 60B) on the bottom of the door. You should then be able to remove and replace that glass.

You can order the foil from this page: Sears PartsDirect.com .

I hope that this information helps. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician replace that oven door glass, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 10, 2012
A:

If you can properly install that new glass without removing the oven door then that should be okay. Be sure that you attach the foil tape to the new pane of glass before installing it. Also, be sure that you remove all of the residue from the old glass panel before inserting the new one in the door. If that new glass panel is not lined up properly, then it may endure some uneven pressure on the corners and break again. Residue from the old glass panel could prevent the new glass panel from being lined up properly. I recommend that you remove the oven door if you suspect that there may still be residue from the original panel inside the door assembly. Make sure that the range is level and "racked" properly (square and even in the cabinet). A problem with the leveling or "racking" of the range could also cause that oven door glass to break in the manner that you described.

Read More
Lyle W -
Sears Technician
December 10, 2012
A:

It is difficult to accurately anticipate the cause of that failure. The glass panel could have had a defect that finally gave way and caused that failure. The glass panel may have encountered an impact at some point previous to the failure. That impact may have damaged the panel even though it did not actually break until later on as you described. There have been known issues with the glass oven door panel breaking when the range is not properly leveled or racked. That uneven pressure on the glass panel does not always cause an immediate breakage. The pressure can be exerted for years until the glass panel finally breaks due to uneven forces exerted on the corners or edges of the glass panel. I hope that this information helps. If you need more assistance, reply with additional details.

Read More
Lyle W -
Sears Technician
December 10, 2012
A:

You may have seen the foil on the previous glass panel. The parts diagram above shows the placement of the foil (Keys 14 and 14a). It is a foil tape so it will have a sticky side that will adhere to the glass. The foil acts as a heat shield for the glass.

Read More
Lyle W -
Sears Technician
December 11, 2012
A:

That part 14 will go across the very top of the glass. It will normally need to be nearly flush with the top of the glass panel so that it is not seen through the see-through portion of the panel. The side pieces of foil will need to be positioned in a similar manner along the sides of the glass so that they will not be in the see-through portion of the glass. They do not have to overlay part 14 but they should be as close as possible to the bottom of that upper strip. I hope that this additional information helps. If you need more assistance, let us know.

Read More
Lyle W -
Sears Technician
December 13, 2012
See more answers