Model #79075752100 KENMORE Free Standing, Gas

  • Backguard
    3 Results
  • Burner
    3 Results
  • Body
    3 Results
  • Top/drawer
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

oven flashes f9 oven door lock cycles

A:

As indicated in the links provided by Maira in the above response, the F9 does indicate that the electronic control board in the console detected a problem with the oven door lock assembly. You could have a problem with the door lock motor or a mechanical problem with the linkage. A wiring failure or a bad electronic oven control board could also cause this problem.

The oven door lock motor assembly is on the back of the range. It is circled in green on the image below. That exact range in the picture is different than yours but the door lock motor assembly is in the same location. You can unplug the range and shut off the gas supply. Pull the range out and check the wiring connections on this component. Remove the lower back panel to access this area. You can also remove the upper back panel and check the wiring connections on the electronic control board in the console. The second image below shows the wiring diagram for your exact model of range with the circuits for the lock system traced in colors. This should help you check the wiring.

If you find no problems with the wires, I recommend that you check to make sure that the rod and latch assembly are not bound up. If you find no problems there, you will probably need to replace the oven door lock motor assembly (part 316464301). You can order that part from the Sears PartsDirect website. Here is a direct link for that part: Latch Motor .

If you replace the door lock motor assembly and still have a problem then you may need to replace the electronic oven control board in the console.

If you need more help, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 02, 2010
Q:

Problem with Kenmore gas range, model # 7+075752100

A:

Thank you for your question and I understand your concern.

I do not have clear understanding of which gas valve you replaced. I must assume you are speaking of the dual oven safety valve part #5303208499. I also must assume the bake igniter is not glowing at all or it's glowing but the bake burner never ignites because the oven safety valve is not opening. If this is correct, then the bake igniter is likely faulty and needs to replaced. If the bake igniter is not getting voltage then it could have a faulty oven control board.

As far as the broil burner flame is concerned, it sounds like your implying the size or the broiler flame is increasing and decreasing in size. A weak broil igniter could cause this to happen.

Assuming you replaced the oven safety valve and the broiler flame is erratic then it may have a faulty gas pressure regulator or a weak broil igniter. If you did replace the pressure regulator then it likely has a faulty oven safety valve or a weak broil igniter.

Reply with additional details for further assistance if needed. You may need to have a technician come out to diagnose and repair your range. The gas supply may also need to be checked for the proper gas pressure.

This unit is pre-set to operate on 4" natural gas manifold pressure. A convertible pressure regulator is connected to the manifold and MUST be connected in series with the gas supply line. If the LP/Propane conversion kit has been used, follow instructions provided with the kit for converting the pressure regulator to LP/Propane use. The LP kit can be found on the back side of the range. Care must be taken during installation of range not to obstruct the flow of combustion and ventilation air. For proper operation, the maximum inlet pressure to the regulator should be no more than 14 inches of water column pressure. The inlet pressure to the regulator must be at least 1 inch greater than regulator manifold pressure. Examples: If regulator is set for natural gas 4 inch manifold pressure, inlet pressure must be at least 5 inches; if regulator has been converted for LP/Propane gas 10 inch manifold pressure, inlet pressure must be at least 11 inches.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
March 16, 2011

Top Parts