Model #77-8957-00-03 Tappan ranges, electric

  • Cover Page
    3 Results
  • Cooktop Parts
    3 Results
  • Lower Oven Door Parts
    3 Results
  • Lower Body Parts
    3 Results
  • Broiler Parts
    3 Results
  • Drawer Parts
    3 Results
  • Control Panel
    3 Results
  • Top Door Parts
    3 Results
  • Power Control
    3 Results
  • Upper Body Parts
    3 Results
  • Splasher Control
    3 Results

Question and Answers

Q:

Battery size & Voltage on Remote for Garage door opener

A:

Thank you for your question on the size and voltage of the battery for the remote.

Don has given you the correct information on the battery.

This battery is a 12 volt and I have given you a link below for ordering the battery, or you can go to your nearest Sears store in the hardware department to pick one up.

Remote battery .

Battery number A23 .

I hope this information will help.

Sam A.

Read More
Sam A -
Sears Technician
February 08, 2012
Q:

Why does my Kenmore dehumidifier stop working after it shuts off in comfort mode?

A:

In the comfort mode, the unit will work automatically to maintain a humidity level based on the ambient temperature that is being sensed at the unit. You did not indicate what temperature that you actually measured in the room. The temperature measured by the dehumidifier may be a few degrees off. If it is more than 10 degrees off then this would be unusual. Before deciding whether something is wrong, I recommend that you accurately measure the temperature in the vicinity of the dehumidifier with a good thermometer. Since the dehumidifier has an evaporator coil inside, it will normally cool the air in the immediate vicinity of the unit.

Try using other manual settings on the dehumidifier. See if it will operate properly. If it does, then there may be nothing wrong with it.

The dehumidifier has a self diagnostic feature. It will normally display an error code if it detects a component problem.

The remote display works off of RF (Radio Frequency) transmission. You could have RF interference that is preventing the remove from always receiving the signal from the dehumidifier even if it is in close proximity. This could be normal. If it connects most of the time then it is likely okay.

When you turn the unit off and back on, it could affect the temperature being sensed by the thermistor (temperature sensor). It may also affect the humidity being sensed. This could be normal.

I don’t have enough details to help you determine whether the dehumidifier is malfunctioning.

If the unit will not work in other modes, then it could have a problem. If you are certain that it is malfunctioning then it may need service. If it is still under warranty, follow the directions for warranty service in your owner's manual.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
September 18, 2009
Q:

Kenmore ultrasoft 180 625.388180 03

A:

Thank you for your question.

I can understand wanting to know what the small brownish orange balls are.

This is the resin beads that do the softening.

What has happened is that the distributor screen down in the bottom of the resin tank has broken and is letting the resin beads out into the water lines.

To repair this you will need to replace this part and it is not a nice job for a consumer because you have to remove the resin bed tank from the softener and then remove the resin and replace the distributor. This tank is full of water and resin beads and it is very heavy.

You will have to remove all the salt from the storage tank first.

Then remove the head off the top of the resin tank.

Then remove the top distributor screen and then you will see the resin.

If it was me doing this I would replace the resin bed also, since you have lost some and you have not cleaned the current bed before.

The part number for the distributor is: 7105047 and it sells for about $62.00.

The part number for the resin is: 0502272 and it sells for about $150.00.

My suggestion is to activate the bypass valve to the softener is not in the water supply line and while you will not have softened water it will stop the resin beads from getting into the water lines.

If you feel like you can do this repair and need more help please reply and I will be happy to help you further.

[Kenmore Water | http://www.kenmorewater.com/website/animations/product-animation/ts_index.html].

I have given you an interactive link to Kenmore Water.com so you can see how the unit works and it includes troubleshooting information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
April 13, 2011