Model #77-4987-00-05 TAPPAN Ranges, Electric

  • Cover Page
    3 Results
  • Control Panel
    3 Results
  • Lower Oven Door Parts
    3 Results
  • Drawer Parts
    3 Results
  • Top Door Parts
    3 Results
  • Cooktop And Broiler Parts
    3 Results
  • Splasher Control
    3 Results
  • Power Control
    3 Results
  • Upper Body Parts
    3 Results
  • Lower Body Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Why does my Kenmore dehumidifier stop working after it shuts off in comfort mode?

A:

In the comfort mode, the unit will work automatically to maintain a humidity level based on the ambient temperature that is being sensed at the unit. You did not indicate what temperature that you actually measured in the room. The temperature measured by the dehumidifier may be a few degrees off. If it is more than 10 degrees off then this would be unusual. Before deciding whether something is wrong, I recommend that you accurately measure the temperature in the vicinity of the dehumidifier with a good thermometer. Since the dehumidifier has an evaporator coil inside, it will normally cool the air in the immediate vicinity of the unit.

Try using other manual settings on the dehumidifier. See if it will operate properly. If it does, then there may be nothing wrong with it.

The dehumidifier has a self diagnostic feature. It will normally display an error code if it detects a component problem.

The remote display works off of RF (Radio Frequency) transmission. You could have RF interference that is preventing the remove from always receiving the signal from the dehumidifier even if it is in close proximity. This could be normal. If it connects most of the time then it is likely okay.

When you turn the unit off and back on, it could affect the temperature being sensed by the thermistor (temperature sensor). It may also affect the humidity being sensed. This could be normal.

I don’t have enough details to help you determine whether the dehumidifier is malfunctioning.

If the unit will not work in other modes, then it could have a problem. If you are certain that it is malfunctioning then it may need service. If it is still under warranty, follow the directions for warranty service in your owner's manual.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
September 18, 2009
Q:

what does code f 05 mean

A:

The "F05" fault code indicates a Water Temperature Sensor Error. If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, the "F05" error code will be displayed. See image below for further instructions.

Potential Causes:

  1. Check the Water Temperature Sensor resistance. It should measure 9.7K ohms at 86 degrees.
  2. Check connections to the Water Temperature Sensor
You will likely find the wire connection had come loose from the temperature sensor. Without having the model number of your HE3t washer I will not be able to confirm if the heater and sensor is located at the lower backside of the tub or at the front lower section of the tub. Disconnect the power cord from the power source before removing the front lower access panel and checking for loose connections on the temperature sensor.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
August 04, 2010
Q:

Craftsman lawn tractor -- engine seized

A:

Thank you for your question and I understand your concern.

Remove the spark plug and then see if the engine will spin over. If it battery and starter is okay and the engine will not spin over, then the engine very well could have seized up due to the lack of oil circulation when it was on the severe sideway incline.

It would likely cost less to replace the engine rather than having it rebuilt. I was not able to price the replacement engine. The parts list shows the replacement engine is part #311707-0028-E1.  I strongly suggest taking the mower in for an estimate of repair. It may cost less to have the engine replaced but I can't be certain. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link:Sears Home Services.

Read More
Joey S -
Sears Technician
April 18, 2013