Model #73-3751-00-02 Tappan ranges, electric

  • Cover Page
    3 Results
  • Control Panel
    3 Results
  • Splasher Control
    3 Results
  • Cooktop Parts
    3 Results
  • Upper Oven Door Parts
    3 Results
  • Lower Oven Door Parts
    3 Results
  • Broiler Parts
    3 Results
  • Upper Body Parts
    3 Results
  • Lower Body Parts
    3 Results
  • Drawer Parts
    3 Results

Question and Answers

Q:

Why does my Kenmore dehumidifier stop working after it shuts off in comfort mode?

A:

In the comfort mode, the unit will work automatically to maintain a humidity level based on the ambient temperature that is being sensed at the unit. You did not indicate what temperature that you actually measured in the room. The temperature measured by the dehumidifier may be a few degrees off. If it is more than 10 degrees off then this would be unusual. Before deciding whether something is wrong, I recommend that you accurately measure the temperature in the vicinity of the dehumidifier with a good thermometer. Since the dehumidifier has an evaporator coil inside, it will normally cool the air in the immediate vicinity of the unit.

Try using other manual settings on the dehumidifier. See if it will operate properly. If it does, then there may be nothing wrong with it.

The dehumidifier has a self diagnostic feature. It will normally display an error code if it detects a component problem.

The remote display works off of RF (Radio Frequency) transmission. You could have RF interference that is preventing the remove from always receiving the signal from the dehumidifier even if it is in close proximity. This could be normal. If it connects most of the time then it is likely okay.

When you turn the unit off and back on, it could affect the temperature being sensed by the thermistor (temperature sensor). It may also affect the humidity being sensed. This could be normal.

I don’t have enough details to help you determine whether the dehumidifier is malfunctioning.

If the unit will not work in other modes, then it could have a problem. If you are certain that it is malfunctioning then it may need service. If it is still under warranty, follow the directions for warranty service in your owner's manual.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
September 18, 2009
Q:

I am getting a F7 02 code on my kenmore electric range model # 790.4661. I have read many of the questions and answers but still need help.

A:

I understand your concern and since you have already replaced the Oven Control/Clock Timer and it' still displaying the fault codes we can assume the failure is likely the touch panel.

The "F701" fault code is likely caused by a loss of a keyboard tail connection.

The "F702" fault code is likely caused by a shorted keypad.

Since the Electronic Oven Control (EOC) has been replaced, the failure is likely the Glass Touch Panel providing you do not have a loose keyboard tail connection.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services

Read More
Joey S -
Sears Technician
November 18, 2010
Q:

what is error code F 02 mean

A:

Thank you for your question and I understand your concern.

The "F02" fault code displays when the drain time exceeds 8 minutes. This can happen if the drain pump filter is restricted or if there is too many suds due to the wrong type of detergent being uses or too much detergent being used.

I added an image below showing how to access the drain pump filter. NOTE: Be sure to have all the water removed from the tub before removing the drain pump filter. You will also need to disconnect the power cord from the power source before removing the front lower access panel.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
July 05, 2011