Model #730 PORTER CABLE drill driver

  • Drills
    3 Results

Question and Answers

Q:

Proform 730 motor runs fine, then stops

A:

Thank you for your question.  There are a few reasons your treadmill is slowing down or stop when you step on the belt.  1. If the walking belt or drive belt is too loose the treadmill will slow down when you walk on it, but it will not slow down if it is running with no load. That is because the belt is slipping. If you only adjusted the walking belt and not the drive belt, the drive belt could be slipping. To adjust the drive belt you will have to remove the motor hood. The drive belt is located between the motor and the front roller. To adjust the drive belt first, unplug the treadmill and remove the motor cover. Next, locate and loosen the motor mounting bolts. Then move the motor so that the belt is tight and have someone retighten the mounting bolts. It will take quite a bit of force to hold the belt tight. After the belt is tight plug the treadmill in and carefully test the operation. If the belt still slips, watch the front roller. If the roller stops but the pulley does not the roller is defective. If the roller and the pulley stop, the drive belt is still loose.    As far as the walking belt goes, it should be adjusted to be able to lift it approximately 2 to 3 inches at either side of the middle of the belt. I have provided the instructions for adjusting the walking belt below. 2. If the walking belt slows down under a load and both belts are adjusted correctly the walking belt could be dry and in need of lubrication, especially if you have it in a garage. Having it in a garage is a not a good thing the dust and dirt get into the wax on the bottom of the walking belt and grind down the walking board surface causing drag. A dry walking belt is the most likely the problem.To correct this problem apply some deck wax, NOT Silicone, to the walking board. There is a lube kit available as well as a single tube. Both come with installation instructions, the part number for a single tube of wax is 219168 for $3.99, the part number for the kit which includes 3 tubes of wax, an application wand and a case is 219170 for $29.99 and they are available at Sears Partsdirect . Just in case the lube does not come with instructions, I will add them. Turn the walking belt until the belt seam is along the top of the front roller. Raise the belt on one side in the center of the walking board front to back as high as you can. Apply 1/2 the tube of lubrication to the walking board in a zig zag fashion moving from front to back. Move the belt until the seam comes up on top of the rear roller and lift the belt again and put the rest of the lubrication on the walking board in the same manner. Turn the treadmill on and walk on the belt for 10-20 minutes. Walk all over the belt to distribute the lubrication evenly on the walking belt and board. I hope this helps. If I can be of further assistance, please feel free to reply below.  Thanks for using Manage My Life. Mark T.

Read More
Mark T -
Sears Technician
March 04, 2013
Q:

I have a Pro-Form 730 Treadmill. Is it easy for DIYer's to replace the left and right link arms?

A:

Replacing the link arms is fairly simple if you have the right tools and some patience. You will have to remove the nut on the inside of the treadmill frame that holds the upright frame to the treadmill. Spread the upright and remove the slider and washers for the link arm.

There are several spacers and washers involved that will fall off as you remove these parts. You have to get them back in their correct places.

Read More
Jimmy K -
Sears Technician
November 21, 2008
Q:

How do you replace the walking belt on Pro-Form 730 Treadmill (Mdl #831.297940)?

A:

Thank you for your question.

Replacing the belt on your treadmill is fairly difficult and time consuming. In addition, there are no really detailed instructions for replacing it since a professional would typically do that type of service.

The basic instructions are listed below to help you.

  1. Unplug the treadmill from the power source.
  2. Remove the motor hood on the front of the treadmill.
  3. Remove the right and foot rail.
  4. Remove the rear roller adjusting bolts.
  5. Remove the front roller adjusting bolt. Make sure to count the number of turns it takes to remove the bolt. Then when you reinstall the bolt, you can get it in the same place.
  6. Remove the front roller.
  7. Remove the screws from the walking board. Then lift the walking board and slide the walking belt off the board.
  8. Reverse the instructions to reassemble the treadmill.
I have added the instructions for adjusting the walking belt below. Again, this is a fairly involved repair, so if you have any concerns or reservations you may want to consult a professional.

I hope this is helpful. Please reply below if you need further assistance. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
November 15, 2010