Model #66575014101 Kenmore free standing, gas

  • Cooktop
    3 Results
  • Control Panel
    3 Results
  • Manifold
    3 Results
  • Chassis
    3 Results
  • Door
    3 Results
  • Drawer Amd Broiler
    3 Results

Question and Answers

Q:

Why does our Kenmore gas range model 66575014101 start displaying the code E2 F2?

A:

The F2 fault code indicates a problem with the keytail ribbon connection from the keypad or a failed keypad. This F2 fault code is normally paired with the E0, E1 or E6 error codes. I do not see the E2 error code paired with the F2 fault code in the technical information for this range. Given the F2 fault code, it is likely that you either have a keytail ribbon connection problem or a failed keypad. If you are able to unplug the range and access the control board in the console (remove the upper back panel), then you can check the keytail ribbon connection of the keypad to the control board. If the connection looks okay, then I recommend replacing the keypad.

You can order the membrane switch keypad from the Sears PartsDirect website. Use your model number to access the parts list and measure the correct color.

If you are not completely confident in your technical ability to safely access the components and diagnose/repair this failure, I recommend calling a service technician.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
Q:

On Kenmore Gas stove model 665-75014101 do I have to pull it out to replace the sensor?

A:

I don't think that you should have to pull the range out to replace the sensor probe. You will need to unplug the range or shut off the circuit breaker to disconnect electrical power. If you don't want to pull the range out and unplug it, you can shut off the circuit breaker.

Open the oven door and see if the sensor probe is mounted with screws that are visible from the inside of the oven cavity as shown in the first image below. If it is then you can use the procedure shown in that first image to replace the sensor probe. NOTE: You may need to remove the oven door to gain easier access to the sensor probe. The procedure for removing the oven door is in your owner's manual. Here is a link for that manual in case you need it: Owner's Manual .

If the sensor is mounted from the back of the oven as shown in the second image, then you will need to pull the range out and remove the lower back panel (with the range unplugged ).

This information should help you replace the sensor probe. If you need more assistance, reply with additional details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 07, 2010
Q:

Why won't my Kenmore oven reach the set temperature?

A:

This oven uses a Direct Spark Ignition (DSI) system to light the burners in the oven (and on the cook top). This is a complicated system that is difficult for many service technicians to diagnose and repair (especially when you have an intermittent problem). A failed control board, a bad thermistor (temperature sensor), a wiring problem, a gas flow problem, reverse polarity on the power cord wiring, a grounding problem, a failed bake or broil gas valve or a failed DSI control could cause this problem. I normally recommend that you have a service technician diagnose and repair this type of failure.

If you are confident in your technical ability to safely perform some checks, here is some information that may help you:

When the burner is lit, check the flame to make sure that it is the correct size and shape. You may need to adjust the air shutter. This process is described in the installation instructions for the range. Here is a link for the installation guide if you need it: Installation Instructions .

I provided the wiring diagram for your model of range in the image below. Here is a link for information regarding the DSI system: Where can I find specific procedures for checking the control board functions on my Whirlpool gas range model TGS325MQ4? If you are able to safely use this information, you may be able to determine the cause of your failure. NOTE: This information is intended for technicians. Follow electrical and gas safety guidelines. Do not attempt any check that you are not completely confident that you can safely execute. The diagnosis of this system normally require live voltage checks. I do not recommend that you conduct these types of checks yourself. Contacting a live wire in the range can result in lethal electrical shock. If you do conduct live voltage checks, use extreme care.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
September 24, 2009

Recommended maintenance parts & accessories

Show 3 more
No more item to show