Model #615-2G Amana air conditioner -room

  • Exterior Parts
    3 Results
  • Interior Parts
    3 Results
  • Insulation Kit Parts
    3 Results

Question and Answers

Q:

Why is the belt slipping on my Proform XP 615 treadmill?

A:

You did not indicate whether you lubricated the belt using the part 219168. I recommend that you try this remedy before replacing the belt.

Many different factors could be causing the belt to slip. Without a physical examination of the treadmill, it is difficult to determine the exact cause of the problem that you are having.

Most treadmills only have a 90 day warranty. Replacement of the belt would not be covered since the treadmill is 2 years old.

I understand your concern regarding the performance of this treadmill that has a slipping belt after only 2 years. A treadmill will normally last several more years before you experience any problems with the belt. Certain factors such as frequency of use and the environment that it is stored (or used) in can affect the longevity of the belt. I am not aware of any common problems with the Proform treadmills. Although we can offer technical help and advice, we are not in a position to directly address your satisfaction concerns regarding this treadmill. We do want to get you in contact with someone who can address this issue. I recommend that you call the Sears National Customer Relations Office at 1-800-549-4505 to discuss the performance of this treadmill and your satisfaction with this product.

Read More
Lyle W -
Sears Technician
March 26, 2010
Q:

how to change a motor belt on the treadmill proform xp 615?

A:

If the drive belt of the treadmill is slipping, you should be able to adjust it. To adjust the drive belt remove the cover. Now loosen the bolts that mount the motor. By hand, pull the motor back so the belt is tight. Now have someone tighten the mounting bolt while you hold the motor. Now carefully walk on the treadmill and make sure the belt is not slipping.

If you think, you need to replace the drive belt the instructions are listed below. We do not have any written instructions for replacing the drive belt of a treadmill. Please follow the steps below to aid you in the belt replacement.

  • Unplug the treadmill and remove the motor cover. The cover has three screws along the front and screws from the bottom.
  • Loosen the rear roller adjusting bolts.
  • Loosen the bolts that mount the motor to loosen the belt.
  • Remove the bolt in the front roller opposite of the pulley. Count how many turns it takes to remove it. When you are putting it back together, turn the bolt the same number to insure the same placement of the front roller.
  • Remove the roller and replace the belt.
  • Reassemble in the reverse order.
  • You will have to push down on the motor to tension the drive belt. When pushing down have someone else tighten the mounting bolts.
  • I have provided the instructions of how to adjust the walking belt.

Please let me know if you need further assistance.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
November 09, 2010
Q:

My Pro Form XP 615 trainer will not start

A:

Thank you for your question.

I am sorry you are having a problem with the treadmill. I will be happy to assist you with repairing the treadmill. To diagnose the treadmill you will need a volt ohmmeter and feel comfortable making life voltage checks. If you have a meter and feel confident in making, the checks use the image below. First, unplug the treadmill and remove the motor cover. Then turn the meter to check AC voltage. Plug the treadmill in and place the meter on the AC wire marked in the image. You should have at least 110 volts. If you do not have this reading, check the power to the treadmill and the wiring. If you do have the reading, turn the meter to check DC voltage to the console. The image below shows where to make the checks. When you place the leads on the wires, you should have a reading of 8 to 12 volts. If you have this voltage, the console is defective. If you do not have this reading check for the same voltage out of the motor control board. If you have the reading, the harness is defective. If you still do not have the reading, the motor control is defective.

Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
February 29, 2012
A:
Mark T -
Sears Technician
February 29, 2012
See more answers