Model #590 Sub-zero side-by-side refrigerator

  • Door
    3 Results
  • System View
    3 Results
  • Cosmetic View
    3 Results
  • Technical Data
    3 Results
  • Model 590 #m/p1004775-#m965870-m966269
    3 Results
  • Technical Data
    3 Results

Question and Answers

Q:

Belt slipping on ProForm 590 LS Crosswalk - I tried tightening and loosening the allen wrench screws in the back, but to no avail. Any other advise to fix?

A:

Thank you for your question.

If the treadmill belt still slips after adjusting the walking belt the problem is most likely a loose drive belt. The drive belt is located between the motor and the front roller. To adjust the drive belt first, unplug the treadmill and remove the motor cover. Next, locate and loosen the motor mounting bolts. Then move the motor so that the belt is tight and have someone retighten the mounting bolts. It will take quite a bit of force to hold the belt tight. After the belt is tight plug the treadmill in and carefully test the operation. If the belt still slips, watch the front roller. If the roller stops but the pulley does not the roller is defective. If the roller and the pulley stop, the drive belt is still loose. If the walking belt is too tight, the motor will over heat and cause the hot smell. I have provided you with an image below showing how to correctly adjust the walking belt. Also if the underside of the belt feels sticky you may want to order and apply belt lube. This will keep the treadmill operating smoothly. The part number for the belt lubrication kit is 219168. You can buy it at [www.searspartsdirect.com]. The cost is around $4.00. The application instructions should be in the package, but in case they are not here is how to apply the lubrication. Turn the walking belt until the belt seam is along the top of the front roller. Raise the belt on one side in the center of the walking board front to back as high as you can. Apply 1/2 the tube of lubrication to the walking board in a zig zag fashion moving from front to back. Move the belt until the seam comes up on top of the rear roller and lift the belt again and put the rest of the lubrication on the walking board in the same manner. Turn the treadmill on and walk on the belt for 10-20 minutes. Walk all over the belt to distribute the lubrication evenly on the walking belt and board. Please let me know if you have any other questions. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
January 03, 2011
Q:

proform 590 LS crosswalk tredmill 831299620

A:

Thank you for you question.

I see that you have gotten the manual. Once you have the link opened, you can save a copy to your computer and/or print a copy.

Please let me know if you need further assistance on the treadmill.

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
February 26, 2011
Q:

Subzero Model 590 Ice Maker malfunction

A:

According to your details, you are probably correct about the ice maker failing to eject the ice cubes and then trying to refill the ice mold with water even though it still has ice cubes in it.

We have limited technical information on this model of SubZero refrigerator. I also had trouble finding replacement parts for that ice making system. Based on your details, the ice maker assembly (part 4-20-052-0) would probably need to be replaced. I do not find that part available through our Sears Parts system or through other parts sources that I checked.

You can unplug the refrigerator and manually defrost that ice mold using a heat gun or hair dryer on a warm setting. Remove the ice from that ice mold and see if the ice maker will begin ejecting the ice properly. This may fix your problem.

If the ice maker still won't cycle properly, then you could schedule service through this link: Sears Home Services . NOTE: Keep in mind that if parts are not available for that repair, the technician may not be able to fix the ice maker even though you would need to pay for the service call.

If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
January 05, 2012