Model #41799680410 KENMORE Laundry Centers/Combos

  • Drum
    3 Results
  • Blower And Base
    3 Results
  • Control Panel
    3 Results
  • Top And Cabinet
    3 Results
  • Tub, Basket, And Agitator
    3 Results
  • Gearcase/transmission
    3 Results
Find part by diagram >

Error Codes

Error Code:



Question and Answers


Not much air flow from dryer 41799680410 Kenmore Laundry center


Thank you for your inquiry on your Kenmore Laundry Center, Model: 417.99680410. From reviewing the details on your model, it appears that your symptoms indicate that you might have a problem with a clogged vent.  I have included a link below to a troubleshooting guide which explains the vent flow process.

Click Here

Safety Warning: Before beginning the repair, disconnect the direct power supply to the dryer to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663

I hope this answered your question. Thank you for contacting, and have yourself a wonderful day. 

Read More
Gerry93 -
Sears Technician
March 03, 2015

tub seal replacement 41799680410


Thank you for choosing and being a valued member. I can certainly assist you in locating the instructions to install the tub seal on your washer.

 Remove power to the laundry center. Remove the panels above the washer there should be two. You will be removing the washer from under the dryer. Remove the front panel on the washer and remove the wire harness to the motor and pump. * Remove the screws that secure the washer base to the cabinet. * Remove the drain hose from the pump and the sump hose from the tub to the pump. Slide the washer tub and base out of the cabinet. * Remove the agitator and the top tub ring. Locate and remove the two screws on the agitator transmission shaft basket locking block.

After you remove the basket, you will probably need to put a bolt or two back into the trunnion without the basket in place. After loosening the bolts on the trunnion that hold the lockplate on the agitator shaft, you can tap the bolts on the outside of that trunnion to break it free and then remove it.

Once you get the trunnion off, you should be able to remove and replace the tub seal (part 5303279394).

You can also visit for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
November 10, 2014

Dryer stops 41799680410


Thank You for choosing Sears I regret to hear that you are having issues with your dryer and do understand your frustration. Glad to help out. Im looking at your model number 41799680410 and I suspect that the dryer motor is overheating because of a lint build up. Inspecting the vent system should be done from time to time to prevent a fire hazard. Pull the dryer out and vacuum all th lint that may be around the motor. 

Clean the lint screen. If you use dryer softener sheets, wash the screen with water and then completely dry it. The lint screen will need to be clean for this test. 

Disconnect the flexible vent hose behind the dryer so that it will temporarily vent directly into the laundry room for this test. Position the dryer so that you can check the air temperature going out of the vent behind the dryer. Ventilate the laundry room as much as possible. 

Fill the drum with a medium load of wet towels. The drum needs to be loaded with wet laundry to accurately check the cycling of the element. 

Start a cycle on high heat. 

Monitor the temperature coming out of the vent behind the dryer. The dryer should heat up to about 150 to 160 degrees. It should then shut off until the temperature decreases 10 to 15 degrees. The dryer should cycle between about 140 and 160 degrees. 

If the dryer cycles properly while venting directly into the laundry room then a restriction in the exhaust vent system to the outside of your home is causing your heating problems. Clean the vent duct thoroughly (or have an outside service clean the vent duct system). 

The high limit thermostat could be opening too soon to cycle the heating element off. The high limit thermostat should not open unless it reaches 250 degrees. You can test this thermostat with a heat gun (hair dryer) to see if it is opening at a lower temperature. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link above to be taken to the page. If you have further questions please resubmit your question for further information.
Thank you for choosing Sears

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.  

Read More
Sherman_G_Wallace -
Sears Technician
April 25, 2014

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show