Model #37-1048-23-05 TAPPAN Ranges, Electric

  • Cover Page
    3 Results
  • Body Parts
    3 Results
  • Cooktop And Broiler Parts
    3 Results
  • Door Parts
    3 Results
  • Backguard
    3 Results
Find part by diagram >

Question and Answers

Q:

Expert Joey S.. I looked up parts number .. doesnt existed

A:

Thank you for your question and I understand your concern.

I double checked the part number of the Bake ignitor (5303935066) and it is a good part number. You can order from SearsPartsDirect . Click on the link and will take you to directly to the page. It will list 4 of the same part numbers. It will be a universal ignitor that will fit many different models.

Read More
Joey S -
Sears Technician
July 27, 2011
Q:

GE profile top freezer too warm

A:

We can likely provide some technical tips that may help you resolve this problem but we will need to have the model number of your GE Profile refrigerator.

Here are some general tips that may help:

  • Check the back wall of the freezer for excessive ice or frost when the cooling deteriorates. A problem with the automatic defrost system could be causing the temperature fluctuations.

  • Monitor the compressor motor when the freezer is too warm. If the compressor is not running, you could have a problem with the control, the compressor or the wiring.

An intermittent problem can be difficult to diagnose. As noted above, reply with the model number and we will try to provide some detailed troubleshooting tips.

Read More
Lyle W -
Sears Technician
January 01, 2011
Q:

oven gas doesnt ignite.. just fills up with gas... broiler works stove top works... just oven will not work...help

A:

Thank you for your question and I understand your concern.

CAUTION; DO NOT use the bake feature until your range has been repaired. Based on your symptom and details the bake igniter is too weak to allow the gas valve to open fully/properly in order to ignite. If the bake burner is clean and intact (not broken or rusted out) then the current draw of the bake igniter should be tested. Also make sure the bake igniter is mounted up against the burner and not tilted and hanging down by one screw. The gas must flow to the bake igniter in order to ignite the burner.

I added an image below with the theory of the bake operation and how to check for a weak bake igniter. You will need a clamp on amperage meter in order to check the current draw of the bake igniter. If the bake igniter is not pulling a minimum of 2.9 amps; replace the igniter. The bake igniter is part #5303935066 and it can be ordered from Sears PartsDirect The bake igniter glow bar should pull a minimum of 2.90 amps in order to open and keep the gas valve open. If the igniter is only pulling 2.79 amps or less it may not be sufficient to open the oven safety valve properly. Use caution when checking the current draw and do not have your face over the bake burner when checking the current draw.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
July 26, 2011
A:

The it appears there is mistake in the parts list. I added a link with with the Burner page and image from Sears Parts Direct. The Bake igniter is key #19 which will be a universal ignitor . Here is the link: http://www.searspartsdirect.com/partsdirect/part-model/Tappan-Parts/Range-Parts/Model-3039822305/1269/0124002/Y2700755/00004?blt=06&prst=0&shdMod=30-3982-23-05

Read More
Joey S -
Sears Technician
July 29, 2011
See more answers