Model #358351800 CRAFTSMAN Chainsaw, Gas

  • Chassis/bar/handle
    3 Results
  • Shield/cylinder/crankshaft
    3 Results
Find part by diagram >

Question and Answers


Igntion Module 358351800 Craftsman Chain saw


Thank you for your inquiry on your Craftsman Chain Saw, Model: 358.351800.  From reviewing the details on your model, it appears that the gap on the ignition module is 0.025.

Safety Warning: Before beginning the repair, disconnect the direct power supply to the chain saw to prevent the risk of injury or any electrical shock.

If you don’t feel comfortable or confident in this repair, then you can have it repaired at home by a sears technician. I have the included a link to the website: Sears Home Services or call 1-800-469-4663

I hope this answered your question. Thank you for contacting, and have yourself a wonderful day. 

Read More
Gerry 93 -
Sears Technician
April 07, 2015

Carburetor replacement 358351800


Hello glad to help.  Thank You for choosing Sears
I am sorry and do understand your frustration when there are problems with the chain saw.
Glad to help out.   Im  looking at your Craftsman Chain Saw model number 358351800.

Over the last few years, lots of small engines have had fuel problems being of using gas left in a tank for a while, (not being fresh) and the gas that you use is very bad ethanol.   Very hard on carburetors, fuel lines, fuel filters.   If you have liked  your chain saw,   Want to repair it.   I would get the carburetor, both fuel lines, fuel filter, and fuel stabilizer.   Put that fuel stabilizer in your fresh gas and pour in all  your small engines and it will save you alot of wear and tare for the future use.

 for model 358.351800

Large fuel line 
 for model 358.351800

Small fuel line 
 for model 358.351800

Fuel filter 
 for model 358.351800

Fuel stabilizer for model 358.351800

Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our

Read More
Larry L -
Sears Technician
April 24, 2014

fuel line routing for chain saw 358351800 Craftsman Chain saw


Hello Martin and thanks for the inquiry and for using

Fuel line routing on chainsaws can differ, and the assembly of the lines are one of the things the manufacturers don't specify in great detail. However, I will be happy to help.

The filter will attach to the end of the small fuel line. This line is the fuel pick up line. The other line is the return line. To install the new fuel line you have to cut the end of the line at a severe angle. Push the angled end into the hole of the tank. Then reach into the fuel tank opening with a long pair of needle nose pliers and pull the fuel line into the tank. Once you have the correct amount in the tank cut the end of the fuel line square and install the fuel filter. The return line only has to hang in the tank about a 1/2 inch. The return line with the little check valve or fitting can pull right up to the hole. The fitting is not necessary in most cases. Very few machines "require" the little check valve to be in place. Many of the new machines do not even have one to start with. It's not a bad idea to put it back in place if you have it and can, but it's not a deal breaker for the machine.  

On the carburetor, the smaller fuel line with filter will connect to the tip on the carburetor that is curved (usually). 

We do not have a model specific diagram for the fuel line routing, but I have posted an image below that may help: 

I have also found a couple of videos for replacing the fuel lines on a Craftsman Chainsaw that may be helpful to see, I have attached those blue links below.

Craftsman Chainsaw Fuel Line Video

Craftsman Chainsaw Fuel Line Replacement 

Hopefully this information helps and let us know if we can be of any further assistance. Thanks for using  


Read More
Jeff Wallace Sr -
Sears Technician
November 16, 2013

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show