Model #358350210 CRAFTSMAN Chainsaw, Gas

  • Cylinder/crankshaft/crankcase
    3 Results
  • Chassis/bar/handle
    3 Results
Find part by diagram >

Question and Answers


CHAIN SAW - MODEL#358.350210


A chainsaw is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached a helpful link below that may provide information to assist you with your question.

Read More
Barbara H. -
October 21, 2011

Thank you for your question on the chain saw oiler not pumping oil.

This chain saw has a worm drive oiler driven off the crankshaft.

You will need to remove the side cover/bar and chain brake off. You can do this by removing the two nuts that secures the side cover.

Please remove the air box cover so you can remove the spark plug.

The clutch has an arrow on the direction to remove it from the crankshaft of the engine.

There is a special wrench for removing the clutch.

However if you use some soft rope and feed it down the hole for the piston to bump up against it will help you remove the clutch by preventing the engine from turning over while you remove the clutch.

Us a flat punch and a small hammer and place the punch behind the arrow and give it a series of quick taps to unscrew the clutch from the crankshaft.

Once you have gotten the clutch off you can remove a small washer and the clutch drum with bearing and the large washer.

Once remove it will expose the two screws that secures the oil to the saw housing over the stub of the crankshaft.

Remove the black bodied pump and examine the threads on the pump and the drive screw that will still be on the crankshaft.

If the threads on the pump are stripped you will need to replace the pump.

The oil pump part number is: 530014410 for less than $10.00.

Check the link below for pump ordering.

Oil pump for saw .

Please let me know what you find out and we can continue to troubleshoot further if needed. E-bay picture below that illustrates the pump parts and oil path fittings.

I hope this will help.

Sam A.

Read More
Sam A -
Sears Technician
October 21, 2011

I have another problem. I took the carb. off of my chainsaw to clean it. Now I can't remember how to run the throttle cable from the trigger to the carb.

Read More
Gary -
October 17, 2015
See more answers

how to replace throtter cable on craftman chain saw model #358.350210 358350210 Craftsman Chainsaw


Thank you for choosing Sears Parts Direct. I can certainly assist you in locating the instructions to install the throttle control cable on your chainsaw. I did look into the model number you have provided and I have found information to assist you. Let me know if this helps.

You will need to remove the side cover from the handle to install the cable into the throttle trigger.

From the back side of the filter box the cable goes through a grommet in a groove cut in the body and into the handle assembly.

The cable has a ball on the end that fits into the trigger.

There is a hole or series of holes in the throttle lever on the carburetor that is spring loaded.

Take the point of the L on the cable and feed it into the hole on the throttle plate and flatten out the L.

When you pull the throttle trigger it will need to pull this throttle plate all the way open and then when you let go of the trigger, the spring on the throttle plate will pull it back and close the throttle back to idle.

You can also visit for parts, diagrams, and repair information.
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
May 08, 2014

How do I route the throttle cable on a craftsman 358.350210 chainsaw?


I have attached a photo of the throttle cable set up on your saw. I don't have the carburetor anymore for the saw I took a photo of, but you can see how the cable comes across the air filter housing. From there, the end will just connect onto the carburetor.

Let me know if this does not help you and I'll see if I can get some more photos for you. This saw belongs to our shop, so it's not going anywhere. I just don't have the carburetor or the full filter assembly for it.

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
November 25, 2013

Top Parts

Recommended maintenance parts & accessories

Show 3 more
No more item to show