Model #34HN-2TKX-FE Magic Chef range (gas)

  • Door
    3 Results
  • Body Parts
    3 Results
  • Gas Controls
    3 Results
  • Backguard Parts
    3 Results

Question and Answers

Q:

LG WM2032HW error FE

A:

The total cost of repair will depend on the exact failure and or which inlet valve is at fault. It could also have a fault water level pressure switch too. The water pressure switch is $15.99. The service fee is $130.00 which includes labor but not parts. If it is one of the two valves a fault, one valve is $15.49 and the other valve is $37.49.

Read More
Joey S -
Sears Technician
May 11, 2010
Q:

my dryer kenmore model # 402.89032010 spins and shut off and the display say fe

A:

The FE error code indicates that the control board detects a problem with the power supply voltage. I recommend that you check the house circuit breakers or fuses for a problem first. If one of the house fuses is blown, the dryer will not get the 240 volts needed.

If the house fuses or breakers are okay, I recommend that you unplug the dryer and check the outlet cord wiring on the terminal block. Here is a direct link for the installation guide for this dryer: Installation Instructions . Loose or improper wiring on the terminal block can cause this problem.

NOTE: If the dryer is under warranty, then you should call 1-800-469-4663 (1-800-4MY-HOME) for service at this point. If the dryer is no longer under warranty, you may be able to continue with these advanced technical checks:

If the terminal block wiring is okay, I recommend that you carefully check the voltage at the dryer outlet using a volt/ohm meter. The first image below show a diagram with the voltage that you should measure at the dryer outlet. NOTE: You should only check this live outlet voltage if you are completely confident in your technical ability to safely measure it .

If the outlet is okay, you can unplug the dryer and check the wiring connections on the electronic control board. The second image shows the procedure for accessing the control board in this type of dryer (with the power cord unplugged ). The third image shows a wiring diagram with power connections highlighted in the red and yellow. The fourth image shows a photograph of the control board with essential wiring connections highlighted. This information should help you check the wiring connections on the control board. If all of the connections are okay, you could have a bad control board.

You can order parts from the Sears PartsDirect website if you are certain that a component needs to be replaced.

These tips may help you resolve this dryer problem. If you need more assistance, reply with additional details and we will help you further.

If the dryer is not under warranty and you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 15, 2011
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
February 15, 2011
See more answers
Q:

I have and LG Front load washer with a FE error (except turn the F upside down and it will be right) I didn't know how to make it on my computer.

A:

Thank you for your question and I understand your concern. The fault code you have is a indicating a thermistor error. The thermistor should measure between 2.5k and 180k ohms. You will need an ohm meter to test the thermistor.

The thermistor/temperature sensor is located at the bottom front area of the tub. The top and front panel will have to come off to access the thermistor. See image below. NOTE: Disconnect the power cord from the power source before servicing your washer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
March 15, 2011