Model #3314-X50B Singer mechanical sewing machines

  • Attachment Set
    3 Results
  • Attachment Set Page 2
    3 Results
  • Attachment Set Page 3
    3 Results
  • Attachment Set Page 4
    3 Results
  • Arm, Bed, Throat Plate & Bed Slide
    3 Results
  • Arm, Bed, Throat Plate & Bed Slide Page 2
    3 Results
  • Arm, Bed, Throat Plate & Bed Slide Page 3
    3 Results
  • Arm, Bed, Throat Plate & Bed Slide Page 4
    3 Results
  • Arm Top Cover
    3 Results
  • Arm Top Cover Page 2
    3 Results
  • Cover & Add-ons
    3 Results
  • Cover & Add-ons Page 2
    3 Results
  • Needle Bar
    3 Results
  • Needle Bar Page 2
    3 Results
  • Presser Bar
    3 Results
  • Presser Bar Page 2
    3 Results
  • Arm Shaft Drive
    3 Results
  • Arm Shaft Drive Page 2
    3 Results
  • Arm Shaft Drive Page 3
    3 Results
  • Arm Shaft Drive Page 4
    3 Results
  • Hand Wheel
    3 Results
  • Hand Wheel Page 2
    3 Results
  • Tension
    3 Results
  • Tension Page 2
    3 Results
  • Rotating Hook
    3 Results
  • Rotating Hook Page 2
    3 Results
  • Bight Amplitude
    3 Results
  • Bight Amplitude Page 2
    3 Results
  • Needle Position
    3 Results
  • Needle Position Page 2
    3 Results
  • Cam Stack
    3 Results
  • Cam Stack Page 2
    3 Results
  • Feed Regulator Cam
    3 Results
  • Feed Regulator Cam Page 2
    3 Results
  • Buttonholer & Feed Regulator Cam
    3 Results
  • Buttonholer & Feed Regulator Cam Page 2
    3 Results
  • Feed System
    3 Results
  • Feed System Page 2
    3 Results
  • Feed System Page 3
    3 Results
  • Feed System Page 4
    3 Results
  • Electrical Equipment
    3 Results
  • Electrical Equipment Page 2
    3 Results
  • Electrical Equipment Page 3
    3 Results
  • Electrical Equipment Page 4
    3 Results
  • Electrical Equipment Page 5
    3 Results

Question and Answers

Q:

How do I replace a Poulan 3314 chainsaw fuel line?

A:

You can pull the old fuel lines out of the fuel tank and insert the new lines into the holes and force them into the fuel tank. The fuel lines were inserted into the tank as the trimmer was being assembled at the factory.

The larger plastic line is a return for the fuel as you prime the engine. The large line only goes into the tank 1 1/2 or so inches. The small plastic line has a filter or fuel pick up on the end that you must remove and install on the end of the new line. This line needs 2-3 inches of slack inside the tank so the fuel pick up will always stay in the gasoline.

Most of the tanks have enough room inside the opening where the fuel cap goes to allow you to get a pair of needle nose pliers into the tank and catch the new fuel lines and pull them into the tank once you have them started. Some tanks require a pair of needle nose shaped like an L to reach the fuel lines.

Cut the ends of the tubing at an angle to make them easier to start into the holes. I have add a picture below showing how the tubing should be cut. I have replaced the tubing by pushing the pointed end into the tank and grabbing it from inside the tank with needle nose pliers. I have also started the pointed end from inside the tank and pulled it though the hole from the outside of the tank with a pair of pliers.

The purpose of the tight fit (of course) is to seal the tubing to the sides of the hole and prevent fuel leakage. Don't make the holes larger, they will leak. Use a piece of clean wire with a hook bent on the end to fish the small tube out of the tank opening and remove the fuel pick up.

Thank you for using Manage my life.

Here is a link to order any parts you need. Sears Parts Direct .

Read More
Mark T -
Sears Technician
September 06, 2010