Model #32-1042-23-10 FRIGIDAIRE free standing, gas

  • Cover
    3 Results
  • Backguard
    3 Results
  • Backguard
    3 Results
  • Cooktop Parts
    3 Results
  • Door Parts
    3 Results
  • Door Parts
    3 Results
  • Door Parts
    3 Results
  • Door Parts
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Broiler Drawer Parts
    3 Results
  • Broiler Drawer Parts
    3 Results
  • Body Parts
    3 Results
  • Body Parts
    3 Results
  • Body Parts
    3 Results
  • Control Panel
    3 Results

Question and Answers

Q:

Are there horizantal and vertical hold controls on a 10 yr old 32" Sanyo TV? And if so, where?

A:

A TV made around 2000 would most likely not have a vertical hold adjustment since the need for this adjustment has been eliminated by technology. Vertical hold problems are generally described as the image rolling. Horizontal lines (going left to right) and vertical shaking (top to bottom) is a more common symptom of the vertical deflection collapsing. The fact that you hit it on the side to correct it makes me suspect that you have a poor solder connection in this circuit. The exact location and IC will depend on the model but I would look for an IC501 labeled LA7841 and see if there are any ringcracks around the solder joints. Take extreme caution when working on your TV, The tube will hold a harmful charge long after the power has been disconnected. If you cannot identify the flyback and anode lead as well as capacitors visually I would avoid inspecting your board.

I may have misinterpreted your symptom and if you need to ask the question again try to get your model number so I can be more specific.

I may have misinterpreted your symptom and if you need to ask the question again try to get your model number so I can be more specific.

Read More
David A. - Personal Solutions Manager -
Sears Technician
November 03, 2009
Q:

How can I obtain an owners manual for a Craftsman 10/32 snowblower with tracks?

A:

Thank you for your question.

 

I am sorry you are having a problem with finding the manual. I checked our site for the manual but we no longer have a copy of the manual for your model. I looked up other models and found a manual close to yours. Click here to load that manual. The instructions in the manual should match your snow blower. Just make sure to use your model number to order parts. Do not use the part numbers listed in the manual. They may not fit. If the track is catching, I recommend checking the tension of the track first. If it is not tight enough it might rub. The instructions for adjusting the track are located on page 24.   

If you need parts for the snow blower, you can order them from the following link.Replacement parts for a Craftsman snow blower model 356.885000.

 

I hope this is helpful. Please let me know if you need further assistance.

 

Thank you for using Manage my life.

 

Mark T.

Read More
Mark T -
Sears Technician
November 07, 2013
Q:

location of fuse on lawn tractor

A:

Thank you for your question. I am sorry you are having this problem with the tractor. First, make sure the engagement lever is down or the PTO button is pushed in and the brake pedal is fully depressed or the tractor will not attempt to turn over. If you have already done this, I recommend checking the fuse. The fuse is located behind the dash. If the fuse is good, you have a wiring or switch problem. The easiest way to pin point the problem is with a volt meter. If you do not have a meter, you can purchase one relatively cheap. Turn the meter to check dc volts, and then hold the black lead to the black negative battery terminal for all of the voltage checks. Place the red lead on the positive terminal of the battery. The reading should be 12 volts. If you have a 12 volt reading, move the red lead to the first blue dot in the image. Your reading should be 12 volts. If you have 12 volts, have someone sit on the tractor and hold the brake pedal while turning the key for the rest of the checks. While they have the key turned to the start position, move the red lead to the next blue dot. The reading should always be 12 volts. Then move to the next blue dot. If you lose the 12 volts, the problem is between the last blue dot you had the voltage and where you lost the voltage. If you have 12 volts all the way to the white wire on the solenoid, the solenoid or the starter is defective. To determine starter or solenoid short the two large posts on the solenoid together with a screwdriver. There should be a spark it is normal. Once shorted the starter should run. If the tractor still will not run once you get the starting issue fixed, please let me know. I will be happy to assist you with diagnosing that. Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
April 26, 2013
A:

jon, I am glad to hear you have the tractor up and running again. Do not worry you are not the first customer that had this problem. It is more common than you think. I recommend saving this link. It might be helpful if the tractor ever fails to turn over again. Thank you for using Manage my life. Mark.

Read More
Mark T -
Sears Technician
April 28, 2013
See more answers