Model #32-1019-00-10 Tappan range (gas)

  • Cover Page
    3 Results
  • Backguard
    3 Results
  • Burner Parts
    3 Results
  • Body Parts
    3 Results
  • Cooktop And Broiler Drawer Parts
    3 Results
  • Door Parts
    3 Results

Question and Answers

Q:

Are there horizantal and vertical hold controls on a 10 yr old 32" Sanyo TV? And if so, where?

A:

A TV made around 2000 would most likely not have a vertical hold adjustment since the need for this adjustment has been eliminated by technology. Vertical hold problems are generally described as the image rolling. Horizontal lines (going left to right) and vertical shaking (top to bottom) is a more common symptom of the vertical deflection collapsing. The fact that you hit it on the side to correct it makes me suspect that you have a poor solder connection in this circuit. The exact location and IC will depend on the model but I would look for an IC501 labeled LA7841 and see if there are any ringcracks around the solder joints. Take extreme caution when working on your TV, The tube will hold a harmful charge long after the power has been disconnected. If you cannot identify the flyback and anode lead as well as capacitors visually I would avoid inspecting your board.

I may have misinterpreted your symptom and if you need to ask the question again try to get your model number so I can be more specific.

I may have misinterpreted your symptom and if you need to ask the question again try to get your model number so I can be more specific.

Read More
David A. - Personal Solutions Manager -
Sears Technician
November 03, 2009
Q:

How can I obtain an owners manual for a Craftsman 10/32 snowblower with tracks?

A:

Thank you for your question.

 

I am sorry you are having a problem with finding the manual. I checked our site for the manual but we no longer have a copy of the manual for your model. I looked up other models and found a manual close to yours. Click here to load that manual. The instructions in the manual should match your snow blower. Just make sure to use your model number to order parts. Do not use the part numbers listed in the manual. They may not fit. If the track is catching, I recommend checking the tension of the track first. If it is not tight enough it might rub. The instructions for adjusting the track are located on page 24.   

If you need parts for the snow blower, you can order them from the following link.Replacement parts for a Craftsman snow blower model 356.885000.

 

I hope this is helpful. Please let me know if you need further assistance.

 

Thank you for using Manage my life.

 

Mark T.

Read More
Mark T -
Sears Technician
November 07, 2013
Q:

I started my GE self clean oven at 10:00 and electric went off for just a second and came back on and it ran for 10 hrs and won't go off. GE oven

A:

Thank you for your question and I understand your concern.

The electronic oven control will display "F3" fault code when the oven temperature over heats or if the oven temperature sensor Ohm resistance exceeds 2900 Ohms. If leave the power supply off to the range and then re-connect the power and the oven begins to heat, the electronic oven control was likely damaged due to the electrical storm. Since I do not have model number I will not be able identify what type of door locking mechanism it may have or how you would access it. If you have the Owner's manual of the range, it should have one or more model numbers listed on it that would be helpful.

The range/oven will most likely need a new electronic oven control/clock assembly.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post along with the model number on the cover page of the Owner's manual.

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.


Read More
Joey S -
Sears Technician
April 12, 2013