Model #32-1019-00-03 Tappan range (gas)

  • Cover Page
    3 Results
  • Backguard
    3 Results
  • Cooktop Parts
    3 Results
  • Door Parts
    3 Results
  • Broiler Drawer Parts
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Body Parts
    3 Results

Question and Answers

Q:

Battery size & Voltage on Remote for Garage door opener

A:

Thank you for your question on the size and voltage of the battery for the remote.

Don has given you the correct information on the battery.

This battery is a 12 volt and I have given you a link below for ordering the battery, or you can go to your nearest Sears store in the hardware department to pick one up.

Remote battery .

Battery number A23 .

I hope this information will help.

Sam A.

Read More
Sam A -
Sears Technician
February 08, 2012
Q:

Why would my whole house air cleaner not come on?

A:

Make sure that the access cover is closed. The air cleaner has an interlock switch that will prevent it from powering up if this cover is open.

I recommend that you shut off the circuit breaker and check the wiring and installation. I emailed you a PDF file with the installation instructions and other technical data in case you need it. NOTE: Some of this information is intended for technicians. Exercise caution when using this data. Follow electrical safety guidelines. Disconnect electrical power before accessing internal components.

The document that I sent you has a troubleshooting flow chart that may help you determine the cause of this failure.

If you need parts, you can order them from the Sears PartsDirect website.

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .

If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
December 15, 2010
Q:

Kenmore ultrasoft 180 625.388180 03

A:

Thank you for your question.

I can understand wanting to know what the small brownish orange balls are.

This is the resin beads that do the softening.

What has happened is that the distributor screen down in the bottom of the resin tank has broken and is letting the resin beads out into the water lines.

To repair this you will need to replace this part and it is not a nice job for a consumer because you have to remove the resin bed tank from the softener and then remove the resin and replace the distributor. This tank is full of water and resin beads and it is very heavy.

You will have to remove all the salt from the storage tank first.

Then remove the head off the top of the resin tank.

Then remove the top distributor screen and then you will see the resin.

If it was me doing this I would replace the resin bed also, since you have lost some and you have not cleaned the current bed before.

The part number for the distributor is: 7105047 and it sells for about $62.00.

The part number for the resin is: 0502272 and it sells for about $150.00.

My suggestion is to activate the bypass valve to the softener is not in the water supply line and while you will not have softened water it will stop the resin beads from getting into the water lines.

If you feel like you can do this repair and need more help please reply and I will be happy to help you further.

[Kenmore Water | http://www.kenmorewater.com/website/animations/product-animation/ts_index.html].

I have given you an interactive link to Kenmore Water.com so you can see how the unit works and it includes troubleshooting information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
April 13, 2011