Model #32-1012-45-09 FRIGIDAIRE Free Standing, Gas

  • Cover
    3 Results
  • Backguard
    3 Results
  • Backguard
    3 Results
  • Cooktop Parts
    3 Results
  • Door Parts
    3 Results
  • Door Parts
    3 Results
  • Door Parts
    3 Results
  • Door Parts
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Broiler Drawer Parts
    3 Results
  • Broiler Drawer Parts
    3 Results
  • Body Parts
    3 Results
  • Body Parts
    3 Results
  • Body Parts
    3 Results
  • Control Panel
    3 Results
Find part by diagram >

Question and Answers

Q:

What is wrong when the igniter will glow for 10-12 seconds and then go off with out lighting gas?

A:

The most likely problem is weak solenoid coils on the gas valve assembly. There is always a chance that it's a failed gas valve assembly too. Key# 10 in the image is the gas valve assembly and key# 13 and 14 are the coils. It's recommended to replace both at the same time. I recommend ordering the coil kit which will include both coils. The part number for the coil kit is 279834.

I recommend calling a service technician to diagnose and repair your dryer.

Read More
Joey S -
Sears Technician
April 17, 2008
Q:

The power does not come on my Protron TV.. The cord is good and the tv is only 3 years old.

A:

Unplug the set and plug it back in, hit the power button a few times and repeat. Since you don't mention a power surge or the losing power then it could be a failure in the TV itself. This TV has a power supply board that is in charge of converting your AC into DC and distributing it to where it needs to go. My first guess would be that some filter capacitors have gone bad and the voltage is slightly off. That is why attempting to turn it on multiple times can get it on. This is not a fix but an indicator that you are on the right track. Find a local shop and see if they are willing to take a look inside for you. A lot of the times, the caps are visible swollen and can be replaced to get it working again. If the technician cannot see anything wrong visibly then it becomes a challenge to find what is missing since there is little service information on these sets.

Read More
David A. - Personal Solutions Manager -
Sears Technician
June 02, 2010
Q:

Kenmore Elite Oasis Mdl 28062 purchased 09/08/09

A:

Check the space underneath the washer for any foreign objects that could be in that area. This washer does not have a bottom panel or base. An object underneath the washer could be making the clicking sound.

The motor and rotor are not common failures on this type of washer. You will normally see error codes in the display and the washer will stop when those components are bad. You could have a problem with that outer tub bearing that is causing the clicking noise. With the washer powered off and empty, spin the basket inside the washer and see if it makes a clicking noise when it is rotating. Since you found no items between the basket and the outer tub, your likely problem is in the tub bearing if you hear a noise. You can check the motor by unplugging the washer and disconnecting the water supply hoses. Carefully lay the washer on its back to access the motor. The image below shows how to remove the drive motor. If you are comfortable with removing the motor, you can check that area for problems. With the motor removed, you can spin the basket to see if you still hear the ticking. If you do, then this would confirm your bearing failure unless you can find an item stuck between the basket and the outer tub that is causing this noise.

I checked your owner's manual and found that the outer tub and the spin basket are covered by a 10 year limited parts warranty. You can view the details of that warranty in your owner's manual. Here is a link for that manual in case you need it: Owner's Manual . If that bearing is bad, you would need to pay for the labor of the technician to diagnose and replace the outer plastic tub but you would not have to pay for the part. The labor would probably be around $180. Here is a link for the Sears Service website if you need to schedule service for that type of failure: Sears Home Services .

I hope that this information helps. If you need more assistance, reply with additional details and we will try to assist you further.

Read More
Lyle W -
Sears Technician
April 28, 2011
A:

NOTE: Regarding the outer tub, there have been some improvements made in the service procedure for that outer tub bearing since this answer was posted. The outer tub bearing is now available as a separate component. It can be replaced using special tools that the Sears Service technicians now have been issued. The outer tub that is under a limited parts warranty no longer needs to be replaced when that bearing goes bad in many situations. That bearing kit costs around $80. The labor for the technician would cost around $140 (at this time). That labor would have been charged for the replacement of the outer tub even when the part was covered. This repair may wind up costing about $80 more than it would have when that previous answer was written. If the technician examines that outer tub and the entire tub needs to be replaced instead of just the bearing, then the tub would still be covered by the limited parts warranty. You would still need to pay for the labor of diagnosis and replacement (about $140 at this time). The technician is required to examine the tub and determine the parts that are needed and whether they are covered by the warranty. To repair that likely bearing failure, I recommend that you schedule service by a Sears Technician. You can call 1-800-469-4663 or click on the link that I provided below this response to schedule service.

Read More
Lyle W -
Sears Technician
January 16, 2012
See more answers