Model #314-0510 HYDRO GEAR Transaxle/Transmission, Tractor

  • Hydro Gear Transaxle
    3 Results
Find part by diagram >

Question and Answers

Q:

Where can I get the actual 5-fin fan blade for this unit - part 314 of the diagram is only the clip, I need the fan blade. JV347X1BB Ge Range accessory

A:

Thank you for your question and I understand your concern.

The fan blade is no longer available through Sears Parts. The part number of the fan blade is WB02X8393. If you enter this part number in Google, you may be able to locate one and order it.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
January 18, 2013
Q:

Can you help with installing an expansion tank on lawn tractor model no. 917 271141? It is in the hydro gear transaxle mode.

A:

You can see a parts diagram that will show you the order parts are installed. Go to www.searspartsdirect.com and enter the model number of the tractor. Open the page with the illustration of the hydro-gear transaxle parts.

I hope this helps. We don't have installation procedure for parts such as these.

Read More
Jimmy K -
Sears Technician
July 13, 2009
Q:

How do I remove key 482 from model 536886261 to assist in an auger repair?

A:

To remove key 482 from the impeller shaft, grip the key with the cutting jaws of some diagonal wire cutters and lift it out of the groove in the shaft.

You can use white lithium grease in the gearbox, but you should clean all the old grease out of the gearbox.

I am sending you some instructions for removing the auger and the gearbox from the snow thrower.

To remove the impeller, you will have to remove the auger and gearbox with the impeller.

Remove the auger belt and the pulley from the rear of the auger housing. Remove the bolts and then the bearing for the gear box shaft. Remove both bearings for the auger shaft.

Slide the auger toward either side of the auger housing so the shaft comes out of the side of the auger housing. Pull the loose side of the auger shaft forward until the other end of the shaft comes out of the auger housing.

You can then remove the auger, gear box, and impeller from the auger housing.

If you mean how to remove the auger from the auger housing, follow these instructions. To remove the auger, you will have to remove the auger and gearbox with the impeller.

Remove the auger belt and the pulley from the rear of the auger housing. Remove the bolts and then the bearing for the gear box shaft. Remove both bearings for the auger shaft.

Slide the auger toward either side of the auger housing so the shaft comes out of the side of the auger housing. Pull the loose side of the auger shaft forward until the other end of the shaft comes out of the auger housing.

You can then remove the auger, gear box, and impeller from the auger housing.

If you mean how to remove the auger from the shaft, remove the shear pin and turn the auger, gearbox, and impeller so the auger you want to remove is on top. Pour rust buster on the end of the auger shaft and tap the center of the auger with a hammer from top to bottom. This will help the rust buster to penetrate through the shaft.

You need 2 large pipe wrenches, preferably 24 inch. put the auger assembly down so it is setting on the ground. Place one pipe wrench on the auger you are not replacing to take the load off the gears in the gear box. Place the other pipe wrench on the center hub of the auger you want to remove near the gearbox. Use a 1 1/2 inch pipe around 2 feet long on the handle of the pipe wrench and turn the auger on the counter clockwise. Once you break it loose the auger will unscrew off the shaft.

You should put the auger back on and replace the shear pin. Reverse the pipe wrenches and remove the other auger. Clean both shafts and coat them good with anti seize grease before installing the auger assembly back into the auger housing.

Read More
Jimmy K -
Sears Technician
December 08, 2009