Model #30-3987-00-05 TAPPAN Range (gas)

  • Cover Page
    3 Results
  • Backguard
    3 Results
  • Door Parts
    3 Results
  • Cooktop Parts
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Body Parts
    3 Results
  • Drawer Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Expert Joey S.. I looked up parts number .. doesnt existed

A:

Thank you for your question and I understand your concern.

I double checked the part number of the Bake ignitor (5303935066) and it is a good part number. You can order from SearsPartsDirect . Click on the link and will take you to directly to the page. It will list 4 of the same part numbers. It will be a universal ignitor that will fit many different models.

Read More
Joey S -
Sears Technician
July 27, 2011
Q:

what does code f 05 mean

A:

The "F05" fault code indicates a Water Temperature Sensor Error. If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, the "F05" error code will be displayed. See image below for further instructions.

Potential Causes:

  1. Check the Water Temperature Sensor resistance. It should measure 9.7K ohms at 86 degrees.
  2. Check connections to the Water Temperature Sensor
You will likely find the wire connection had come loose from the temperature sensor. Without having the model number of your HE3t washer I will not be able to confirm if the heater and sensor is located at the lower backside of the tub or at the front lower section of the tub. Disconnect the power cord from the power source before removing the front lower access panel and checking for loose connections on the temperature sensor.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
August 04, 2010
Q:

oven gas doesnt ignite.. just fills up with gas... broiler works stove top works... just oven will not work...help

A:

Thank you for your question and I understand your concern.

CAUTION; DO NOT use the bake feature until your range has been repaired. Based on your symptom and details the bake igniter is too weak to allow the gas valve to open fully/properly in order to ignite. If the bake burner is clean and intact (not broken or rusted out) then the current draw of the bake igniter should be tested. Also make sure the bake igniter is mounted up against the burner and not tilted and hanging down by one screw. The gas must flow to the bake igniter in order to ignite the burner.

I added an image below with the theory of the bake operation and how to check for a weak bake igniter. You will need a clamp on amperage meter in order to check the current draw of the bake igniter. If the bake igniter is not pulling a minimum of 2.9 amps; replace the igniter. The bake igniter is part #5303935066 and it can be ordered from Sears PartsDirect The bake igniter glow bar should pull a minimum of 2.90 amps in order to open and keep the gas valve open. If the igniter is only pulling 2.79 amps or less it may not be sufficient to open the oven safety valve properly. Use caution when checking the current draw and do not have your face over the bake burner when checking the current draw.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
July 26, 2011
A:

The it appears there is mistake in the parts list. I added a link with with the Burner page and image from Sears Parts Direct. The Bake igniter is key #19 which will be a universal ignitor . Here is the link: http://www.searspartsdirect.com/partsdirect/part-model/Tappan-Parts/Range-Parts/Model-3039822305/1269/0124002/Y2700755/00004?blt=06&prst=0&shdMod=30-3982-23-05

Read More
Joey S -
Sears Technician
July 29, 2011
See more answers