Model #30-2139-00-08 TAPPAN Range (gas)

  • Cover Page
    3 Results
  • Backguard
    3 Results
  • Cooktop Parts
    3 Results
  • Door Parts
    3 Results
  • Broiler Drawer Parts
    3 Results
  • Burner, Manifold And Gas Control
    3 Results
  • Body Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Vacuum problem. Bought 02/06/08

A:

Thank you for your question.

I can sure understand your concern as to why you need to hold the hose and handle together to get the Power Mate to work.

• The problem you are having if I understand your description correctly is that the wire connection where the hose meets the handle is not making a good connection all the time.

• There are two other connections that are possible depending on where you are putting the pressure.

• If you are just pushing down on the handle the plug in connections where the lower wand plugs into the Power Mate is one possibility. The other location is where the upper wand plugs into the hose handle assembly.

• If you are pushing on where the hose goes into the handle then it is probably is a broken wire in the hose.

• The wire coils on the hose is what carries the electricity from the vacuum canister to the handle switch and then down the wands to the Power Mate.

• If you can isolate the bad connection to be sure that you are going to be replacing the correct part.

• If it is the hose wires I will give you some pictorial instructions as to how to replace the hose assembly below.

• If it is in the handle harness plug you will need to take the handle apart and replace the handle harness.

• The handle has recessed screws that hold the handle together and one hidden screw at the back of the hand hole to hold the switch cover on.

• The wand wire harness can only be changed with a replacement lower wand.

• If the bad connection is in the Power Mate connection plug you will need to disassemble the Power Mate to replace that harness.

If you have Isolated the problem area please use the link to get more detailed instructions on how to repair.

I hope this will help with your vacuum cleaner.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
November 05, 2010
Q:

drain cycle will not stop bosch shx3ar75uc/08

A:

Thank you for your question and I understand your concern.

There is a float dome inside the tub and if this float is stuck in the up position, it will cause the drain pump to run or if there is too much water in the tank and it's not able to drain, the drain pump will run constantly. The float assembly other than the float dome is located under the tub and left of the sump as shown in the image I added below.

If the dishwasher is not able to drain, the drain pump will run constantly. Check the drain hose and the inside the fitting where the drain hose connects for a blockage.

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

Read More
Joey S -
Sears Technician
August 19, 2013
A:

Fed; The images are at Manage My Life. Copy and paste the URL below in your browser and it will take you to the thread with the images. http://www.managemylife.com/mmh/questions/357022-drain-cycle-stop-bosch-shx3ar75uc08

Read More
Joey S -
Sears Technician
August 21, 2013
See more answers
Q:

Why did my Sears gas range model 362.75875691 stop heating the oven after using it for a long time?

A:

I am not able to access the owner's manual for this range. I did look at the owner's manual for a similar range that uses the identical oven control board. I do not see a control safety feature that limits the time that this oven can be in the bake mode. If the oven restarted normally, then you could have experienced a power surge or glitch through the electrical lines that caused the range to stop baking.

Read More
Lyle W -
Sears Technician